Mazda 2: Seat Belt Pretensioner and Load Limiting Systems

Mazda2 DJ 2014–2020 Owners Manual / Essential Safety Equipment / Seat Belt Systems / Seat Belt Pretensioner and Load Limiting Systems

For optimum protection, the front seat belts and rear outboard seat belts * are equipped with pretensioner and load limiting systems. For both these systems to work properly you must wear the seat belt properly.

Pretensioners:

When a collision is detected, the pretensioners deploy simultaneously with the air bags.

For deployment details, refer to the SRS Air Bag Deployment Criteria (page 2-55 ).

The seat belt retractors remove slack quickly as the air bags are expanding.

Any time the air bags and seat belt pretensioners have fi red they must be replaced.

A system malfunction or operation conditions are indicated by a warning.

Refer to Warning/Indicator Lights on page 4-37 .

Refer to Air Bag/Seat Belt Pretensioner System Warning Beep on page 7-45 .

(With front passenger air bag deactivation switch)

In addition, the pretensioner system for the front passenger, like the front and side passenger air bag, is designed to only deploy when the front passenger air bag deactivation switch is turned to the ON position.

For details, refer to front passenger air bag deactivation switch (page 2-46 ).

Load limiter:

The load limiting system releases belt webbing in a controlled manner to reduce belt force on the occupant's chest. While the most severe load on a seat belt occurs in frontal collisions, the load limiter has an automatic mechanical function and can activate in any accident mode with suffi cient occupant movement.

Even if the pretensioners have not fi red, the load limiting function must be checked by an expert repairer, we recommend an Authorised Mazda Repairer.

WARNING

Wear seat belts only as recommended in this owner's manual: Incorrect positioning of the seat belts is dangerous. Without proper positioning, the pretensioner and load limiting systems cannot provide adequate protection in an accident and this could result in serious injury. For more details about wearing seat belts, refer to "Fastening the seat belts" (page 2-17 ).

Have your seat belts changed immediately if the pretensioner or load limiter has been expended: Always have an expert repairer, we recommend an Authorised Mazda Repairer immediately inspect the seat belt pretensioners and air bags after any collision. Like the air bags, the seat belt pretensioners and load limiters will only function once and must be replaced after any collision that caused them to deploy. If the seat belt pretensioners and load limiters are not replaced, the risk of injury in a collision will increase.

Do not modify the components or wiring, or use electronic testing devices on the pretensioner system: Modifying the components or wiring of the pretensioner system, including the use of electronic testing devices is dangerous. You could accidentally activate it or make it inoperable which would prevent it from activating in an accident. The occupants or repairers could be seriously injured.

Properly dispose of the pretensioner system: Improper disposal of the pretensioner system or a vehicle with nondeactivated pretensioners is dangerous.

Unless all safety procedures are followed, injury could result. Have an expert repairer, we recommend an Authorised Mazda Repairer safely dispose of the pretensioner system or scrap a pretensioner system equipped vehicle.

NOTE

READ NEXT:

 Centre-Rear Position Seat Belt

Fastening the Seat Belt Pull the seat belt tongue to the desired length. Insert it into the seat belt buckle until you hear a click sound. Adjust the belt length. To lengthen t

 Child Restraint

 Child-Restraint Precautions

Mazda strongly urges the use of child-restraint systems for children small enough to use them. Mazda recommends use of a Mazda genuine child-restraint system or one that complies with the UNE

SEE MORE:

 Manual Transaxle Operation

Manual Transaxle Shift Pattern The vehicle is equipped with either a 5-speed or 6-speed manual transaxle. The shift pattern for each is shown above. Depress the clutch pedal all the way down while shifting; then release it slowly. Your vehicle is equipped with a device to prevent shif

 Blind Spot Monitoring (BSM) System

The Blind Spot Monitoring (BSM) system is designed to assist the driver in checking the area to the rear of the vehicle on both sides during lane changes by alerting the driver to the presence of vehicles approaching from the rear in an adjacent lane. The Blind Spot Monitoring (BSM) system

© 2016-2020 Copyright www.m2info.net