Mazda 2: SAS Control Module

SAS CONTROL MODULE REMOVAL/INSTALLATION

WARNING:

CAUTION:

1. Perform SAS control module configuration when replacing it. (See SAS CONTROL MODULE CONFIGURATION).

2. Switch the ignition to off.

3. Disconnect the negative battery cable and wait for 1 min or more.

4. Remove the rear console. (See REAR CONSOLE REMOVAL/INSTALLATION).

5. Flip over the floor covering and disconnect the connectors.

Mazda 2. SAS CONTROL MODULE REMOVAL/INSTALLATION

6. Remove the nuts.

7. Remove the SAS control module in the direction of the arrow shown in the figure.

8. Install in the reverse order of removal.

9. Switch the ignition to ON.

10. Verify that the air bag system warning light illuminates for approx. 6 s and goes out.

SAS CONTROL MODULE CONFIGURATION

1. Connect the M-MDS (IDS) to the DLC-2.

2. After the vehicle is identified, select the following items from the initial screen of the M-MDS.

3. Perform the configuration according to the directions on the screen.

4. Retrieve DTCs by the M-MDS, then verify that there is no DTC present.

SEAT TRACK POSITION SENSOR REMOVAL/INSTALLATION

1. Switch the ignition to off.

2. Disconnect the negative battery cable and wait for 1min or more.

3. Remove the front driver's seat (See FRONT SEAT REMOVAL/INSTALLATION).

Mazda 2. SEAT TRACK POSITION SENSOR REMOVAL/INSTALLATION

4. Remove the connector.

5. Remove the bolts.

6. Remove the seat track position sensor.

7. Install in the reverse order of removal.

8. Switch the ignition to ON.

9. Verify that the air bag system warning light illuminates for approx. 6 s and goes out.

SEAT WEIGHT SENSOR CONTROL MODULE REMOVAL/INSTALLATION

CAUTION:

1. Switch the ignition to off.

2. Disconnect the negative battery cable and wait for 1 min or more.

3. Remove the connector.

Mazda 2. SEAT WEIGHT SENSOR CONTROL MODULE REMOVAL/INSTALLATION

4. Remove the seat weight sensor control module from the bracket by lifting the tab in the direction of the arrow.

5. Install in the reverse order of removal.

6. Switch the ignition to ON.

7. Verify that the air bag system warning light illuminates for approx. 6 s and goes out.

SEAT WEIGHT SENSOR CALIBRATION

CAUTION:

1. Have two 20 kg {44 lb} weights ready to use.

2. Connect the M-MDS (IDS) to the DLC-2.

3. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

4. Then, select item from the screen menu in the following order.

5. Then, select item from the SWS Calibration screen menu in the following order.

6. Perform calibration following the procedures on the M-MDS screen.

SEAT WEIGHT SENSOR INSPECTION

CAUTION:

1. Connect the M-MDS (IDS) to the DLC-2.

2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

3. Then, select item from the screen menu in the following order.

Select the "PassengerSeatWeightSensorRezero".

4. Then, select item from the SWS Calibration screen menu in the following order.

Select the "(2)-When the passenger seat was removed and reinstalled."

5. Perform inspection following the procedures on the M-MDS screen.

SIDE AIR BAG SENSOR REMOVAL/INSTALLATION

WARNING:

1. Switch the ignition to off.

2. Disconnect the negative battery cable and wait for 1 min or more.

3. Remove the following parts:

  1. Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION).
  2. Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION).
  3. B-pillar lower trim (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION).
  4. Front seat belt (See FRONT SEAT BELT REMOVAL/INSTALLATION).

4. Remove the nut.

Mazda 2. SIDE AIR BAG SENSOR REMOVAL/INSTALLATION

5. Remove the side air bag sensor.

6. Disconnect the connector from the side air bag sensor by pressing the connector tab and pulling out the lock lever in the direction of the arrow.

7. Install in the reverse order of removal.

8. Switch the ignition to ON.

9. Verify that the air bag system warning light illuminates for approx. 6 s and goes out.

READ NEXT:

 Clock Spring

CLOCK SPRING REMOVAL/INSTALLATION 1. Switch the ignition to off. 2. Disconnect the negative battery cable and wait for 1 min or more. 3. Remove the following parts: Driver-side air bag module (See

 Air Bag Module and Pre-tensioner Seat Belt Deployment Procedures

WARNING: A live (undeployed) air bag module or pre-tensioner seat belt may accidentally operate (deploy) when it is disposed of and cause serious injury. Do not dispose of a live (undeployed) a

 Inspection of SST (Deployment Tool)

1. Before using the SST (49 H066 002), inspect its operation. Inspection Procedure 1. Follow the steps below to inspect the SST (49 H066 002). If not as indicated in the table, replace the SST (49

SEE MORE:

 Audio Set (Type C/Type D)

NOTE The explanation of functions described in this manual may differ from the actual operation, and the shapes of screens and buttons and the letters and characters displayed may also differ from the actual appearance. Additionally, depending on future software updates, the content may succ

 Fuel-Filler Flap and Cap

WARNING When removing the fuel-fi ller cap, loosen the cap slightly and wait for any hissing to stop, then remove it: Fuel spray is dangerous. Fuel can burn skin and eyes and cause illness if ingested. Fuel spray is released when there is pressure in the fuel tank and the fuel-fi ller cap is

© 2016-2021 Copyright www.m2info.net