Mazda 2: Rear Door Latch and Lock Actuator
REAR DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION
1. To access the glass installation bolt, position the rear door glass so
that the distance from
the top of the rear door glass to the upper part of the rear beltline molding is
approx. 210
mm {8.27 in}.

2. Disconnect the negative battery cable.
3. Remove the following parts:
- Sail inner garnish (See SAIL INNER GARNISH REMOVAL/INSTALLATION).
- Rear door garnish (See REAR DOOR GARNISH REMOVAL/INSTALLATION).
- Rear door trim (See REAR DOOR TRIM REMOVAL/INSTALLATION).
- Rear door speaker (See REAR DOOR SPEAKER REMOVAL/INSTALLATION).
- Rear door glass (See REAR DOOR GLASS REMOVAL/INSTALLATION).
- Rear door module panel (See REAR DOOR MODULE PANEL
REMOVAL/INSTALLATION).
- Rear door latch and lock actuator (See REAR DOOR LATCH AND LOCK ACTUATOR
REMOVAL/INSTALLATION).
4. Remove the screw.

5. Remove the rear door latch and lock actuator.
6. Install in the reverse order of removal.
REAR DOOR LATCH AND LOCK ACTUATOR INSPECTION
1. The following actuator and switch are integrated with the rear door latch
and lock actuator.
Inspect the rear door latch and lock actuator according to each inspection
procedure for the
following items.
- Rear door lock actuator (See REAR DOOR LOCK ACTUATOR INSPECTION).
- Rear door latch switch (See REAR DOOR LATCH SWITCH INSPECTION).

REAR DOOR LATCH SWITCH INSPECTION
1. To access the glass installation bolt, position the rear door glass so
that the distance from the top of the rear door glass to
the upper part of the rear beltline molding is approx. 210 mm {8.27 in}.

2. Disconnect the negative battery cable.
3. Remove the following parts:
- Sail inner garnish (See SAIL INNER GARNISH REMOVAL/INSTALLATION).
- Rear door garnish (See REAR DOOR GARNISH REMOVAL/INSTALLATION).
- Rear door trim (See REAR DOOR TRIM REMOVAL/INSTALLATION).
- Rear door speaker (See REAR DOOR SPEAKER REMOVAL/INSTALLATION).
- Rear door glass (See REAR DOOR GLASS REMOVAL/INSTALLATION).
- Rear door module panel (See REAR DOOR MODULE PANEL
REMOVAL/INSTALLATION).
- Rear door latch and lock actuator (See REAR DOOR LATCH AND LOCK ACTUATOR
REMOVAL/INSTALLATION).
4. Press the latch in using a flathead screwdriver to inspect the latch lever
condition.

5. Verify that the continuity is as indicated in the table.

- If not as indicated in the table, replace the rear door latch and lock
actuator.

REAR DOOR LOCK ACTUATOR INSPECTION
1. To access the glass installation bolt, position the rear door glass so
that the distance from the top of the rear door glass to the
upper part of the rear beltline molding is approx. 210 mm {8.27 in}.

2. Disconnect the negative battery cable.
3. Remove the following parts:
- Sail inner garnish (See SAIL INNER GARNISH REMOVAL/INSTALLATION).
- Rear door garnish (See REAR DOOR GARNISH REMOVAL/INSTALLATION).
- Rear door trim (See REAR DOOR TRIM REMOVAL/INSTALLATION).
- Rear door speaker (See REAR DOOR SPEAKER REMOVAL/INSTALLATION).
- Rear door glass (See REAR DOOR GLASS REMOVAL/INSTALLATION).
- Rear door module panel (See REAR DOOR MODULE PANEL
REMOVAL/INSTALLATION).
- Rear door latch and lock actuator (See REAR DOOR LATCH AND LOCK ACTUATOR
REMOVAL/INSTALLATION).
4. Apply battery positive voltage and connect the ground to each terminal,
and then verify the operation.

- If not as indicated in the table, replace the front door latch and lock
actuator.

READ NEXT:
LIFTGATE LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION
1. Disconnect the negative battery cable.
2. Remove the liftgate lower trim. (See LIFTGATE LOWER TRIM
REMOVAL/INSTALLATION)
3. Disconnect the
KEYLESS RECEIVER REMOVAL/INSTALLATION [KEYLESS ENTRY SYSTEM]
1. Disconnect the negative battery cable.
2. Remove the glove compartment. (See GLOVE COMPARTMENT REMOVAL/INSTALLATION).
3. Remove in the
COIL ANTENNA REMOVAL/INSTALLATION
1. Disconnect the negative battery cable.
2. Remove the column cover. (See COLUMN COVER REMOVAL/INSTALLATION).
3. Disconnect the coil antenna connector.
4. Detach
SEE MORE:
PID/DATA MONITOR DISPLAY
1. Connect the M-MDS(IDS) to the DLC-2.
2. After the vehicle is identified, select the following items from the
initialization screen of
the IDS.
Select "DataLogger".
Select "Modules".
Select "RCM".
3. Select the applicable PID from the PID table.
4. Verify the PID d
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
NOTE
When the battery power is low, or in
places where there are high-intensity
radio waves or noise, the operational
range may become narrower or
the system may not operate
© 2016-2022 Copyright www.m2info.net
