Mazda 2: Power System

POWER SYSTEM LOCATION INDEX

Mazda 2. POWER SYSTEM LOCATION INDEX

  1. Main fuse
  2. Relay
  3. Ignition switch
  4. Key reminder switch

FUSE SERVICE CAUTIONS

CAUTION:

MAIN FUSE REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Remove the main fuse cover in the direction of the arrow while pressing the tab indicated in the figure.

Mazda 2. MAIN FUSE

3. Remove nuts A, B, and C shown in the figure.

Mazda 2. MAIN FUSE

4. Remove the main fuse.

5. Install in the reverse order of removal.

IGNITION SWITCH REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Remove the column cover. (See COLUMN COVER REMOVAL/INSTALLATION).

3. Press tabs A in the direction of the arrow (1) shown in the figure and pull the ignition switch in the direction of the arrow (2).

Mazda 2. IGNITION SWITCH REMOVAL/INSTALLATION

4. Pull the pin in the direction of the arrow shown in the figure and release the lock.

Mazda 2. IGNITION SWITCH REMOVAL/INSTALLATION

5. Pull the connector in the direction of the arrow (4) shown in the figure and remove it while pressing tab B in the direction of the arrow (3).

Mazda 2. IGNITION SWITCH REMOVAL/INSTALLATION

6. Remove the ignition switch.

7. Install in the reverse order of removal.

IGNITION SWITCH INSPECTION

1. Disconnect the negative battery cable.

2. Remove the column cover. (See COLUMN COVER REMOVAL/INSTALLATION).

3. Remove the ignition switch. (See IGNITION SWITCH REMOVAL/INSTALLATION).

4. Verify that the continuity between the ignition switch terminals is as indicated in the table.

Mazda 2. IGNITION SWITCH INSPECTION

Mazda 2. IGNITION SWITCH INSPECTION

KEY REMINDER SWITCH REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Remove the column cover. (See COLUMN COVER REMOVAL/INSTALLATION).

3. Remove the coil antenna. (See COIL ANTENNA REMOVAL/INSTALLATION).

4. Insert the key into the key cylinder and turn the ignition switch to the ACC position.

5. Disconnect the key reminder switch connector.

Mazda 2. KEY REMINDER SWITCH REMOVAL/INSTALLATION

6. Detach the key reminder switch tab.

Mazda 2. KEY REMINDER SWITCH REMOVAL/INSTALLATION

7. Install the key reminder switch in the direction of the arrow.

8. Install in the reverse order of removal.

KEY REMINDER SWITCH INSPECTION

1. Disconnect the negative battery cable.

2. Remove the column cover. (See COLUMN COVER REMOVAL/INSTALLATION).

3. Disconnect the key reminder switch connector.

Mazda 2. KEY REMINDER SWITCH INSPECTION

4. Verify that the continuity between the key reminder switch terminals is as indicated in the table.

Mazda 2. KEY REMINDER SWITCH INSPECTION

Mazda 2. KEY REMINDER SWITCH INSPECTION

RELAY LOCATION

Mazda 2. RELAY LOCATION

  1. Front fog light relay
  2. Starter relay
  3. A/C relay
  4. Horn relay
  5. Cooling fan relay No.1
  6. Headlight relay (HI)
  7. Fuel pump relay
  8. Cooling fan relay No.2
  9. Headlight relay (LO)
  10. Blower relay
  11. Main relay

RELAY INSPECTION

Relay Type

Mazda 2. RELAY

Type A

1. Verify that the continuity is as indicated in the table.

Mazda 2. RELAY

Mazda 2. RELAY

Type B

1. Verify that the continuity is as indicated in the table.

Mazda 2. RELAY

Mazda 2. RELAY

Type C

1. Verify that the continuity is as indicated in the table.

Mazda 2. RELAY

Mazda 2. RELAY

READ NEXT:

 Instrumentation/Driver Info.

INSTRUMENTATION/DRIVER INFO. LOCATION INDEX Oil pressure switch Horn Ambient temperature sensor Instrument cluster Passenger seat belt reminder Fuel gauge sender unit INSTRUMENT CLUSTER REMO

 Control System

CONTROL SYSTEM LOCATION INDEX BCM (body control module) BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION CAUTION: When replacing the BCM, the configuration procedure must be performed before re

SEE MORE:

 PID/DATA Monitor

PID/DATA MONITOR DISPLAY 1. Connect the M-MDS(IDS) to the DLC-2. 2. After the vehicle is identified, select the following items from the initialization screen of the IDS. Select "DataLogger". Select "Modules". Select "RCM". 3. Select the applicable PID from the PID table. 4. Verify the PID d

 Fuses

Your vehicle's electrical system is protected by fuses. If any lights, accessories, or controls do not work, inspect the appropriate circuit protector. If a fuse has blown, the inside element will be melted. If the same fuse blows again, avoid using that system and consult an expert repai

© 2016-2021 Copyright www.m2info.net