Mazda 2: Parking Brake System

Mazda 2 2007-2014 Service Manual / Brakes / Parking Brake System

PARKING BRAKE SYSTEM LOCATION INDEX

Mazda 2. PARKING BRAKE SYSTEM LOCATION INDEX

  1. Parking brake lever
    • (See PARKING BRAKE LEVER INSPECTION.)
    • (See PARKING BRAKE LEVER ADJUSTMENT.)
    • (See PARKING BRAKE LEVER REMOVAL/INSTALLATION.)
  2. Front parking brake cable
    • (See FRONT PARKING BRAKE CABLE REMOVAL/INSTALLATION.)
  3. Rear parking brake cable
    • (See REAR PARKING BRAKE CABLE REMOVAL/INSTALLATION.)
  4. End cable
    • (See END CABLE REMOVAL/INSTALLATION.)
  5. Parking brake switch
    • (See PARKING BRAKE SWITCH INSPECTION.)

PARKING BRAKE LEVER INSPECTION

Stroke Inspection

1. Pull the parking brake lever two to three times.

2. Inspect the parking brake stroke by slowly pulling at point A 50 mm {2.0 in} from the end of the parking brake lever with a force of 98 N {10 kgf, 22 lbf} and counting the number of notches (clicking sound).

Mazda 2. PARKING BRAKE LEVER INSPECTION

Parking brake lever stroke when pulled at 98 N {10 kgf, 22 lbf}

PARKING BRAKE LEVER ADJUSTMENT

NOTE:

1. Remove the console panel. (See REAR CONSOLE REMOVAL/INSTALLATION).

2. Turn the adjusting nut as shown in the figure to adjust.

Mazda 2. PARKING BRAKE LEVER ADJUSTMENT

3. After adjustment, confirm the following points:

  1. Pull the parking brake lever one notch and verify that the parking brake warning light illuminates.
  2. Release the parking brake lever completely, and verify that the rear brakes do not drag.

PARKING BRAKE LEVER REMOVAL/INSTALLATION

1. Remove the rear console. (See REAR CONSOLE REMOVAL/INSTALLATION).

2. Remove in the order indicated in the table.

3. Install in the reverse order of removal.

4. After installation, inspect the parking brake stroke and adjust if necessary. (See PARKING BRAKE LEVER INSPECTION).

Mazda 2. PARKING BRAKE LEVER REMOVAL/INSTALLATION

  1. Parking brake switch connector
  2. Adjusting nut
  3. Bolt
  4. Bolt
  5. Clip
  6. Parking brake lever
  7. Parking brake switch

Bolt Removal Note

1. Move the front seat (LH) forward.

2. Perform the work from the rear seat, flip over the floor covering.

Mazda 2. PARKING BRAKE LEVER REMOVAL/INSTALLATION

3. Remove the bolt.

Clip Removal Note

1. Remove the clip.

Mazda 2. PARKING BRAKE LEVER REMOVAL/INSTALLATION

2. Remove the front parking brake cable from the parking brake lever.

Clip Installation Note

1. Install the front parking brake cable to the parking brake lever.

Mazda 2. PARKING BRAKE LEVER REMOVAL/INSTALLATION

2. Install the clip.

FRONT PARKING BRAKE CABLE REMOVAL/INSTALLATION

1. Remove the rear console. (See REAR CONSOLE REMOVAL/INSTALLATION).

2. Remove the adjusting nut.

Mazda 2. FRONT PARKING BRAKE CABLE REMOVAL/INSTALLATION

3. Remove the TWC. (See EXHAUST SYSTEM REMOVAL/INSTALLATION).

4. Remove the insulator No.1. (See EXHAUST SYSTEM REMOVAL/INSTALLATION).

5. Remove the front parking brake cable from the equalizer.

Mazda 2. FRONT PARKING BRAKE CABLE REMOVAL/INSTALLATION

6. Remove in the order indicated in the table.

7. Install in the reverse order of removal.

8. After installation, inspect the parking brake stroke and adjust if necessary. (See PARKING BRAKE LEVER INSPECTION).

Mazda 2. FRONT PARKING BRAKE CABLE REMOVAL/INSTALLATION

  1. Bracket
  2. Clip
  3. Front parking brake cable

Front Parking Brake Cable Removal Note

1. Separate the floor mat at the area shown in the figure.

Mazda 2. FRONT PARKING BRAKE CABLE REMOVAL/INSTALLATION

2. Remove the front parking brake cable.

REAR PARKING BRAKE CABLE REMOVAL/INSTALLATION

1. Remove the console panel. (See REAR CONSOLE REMOVAL/INSTALLATION).

2. Loosen the adjusting nut shown in the figure only enough that it does not come off.

Mazda 2. REAR PARKING BRAKE CABLE REMOVAL/INSTALLATION

3. Release the parking brake.

4. Remove the TWC. (See EXHAUST SYSTEM REMOVAL/INSTALLATION).

5. Remove the insulator No.1 and insulator No.2. (See EXHAUST SYSTEM REMOVAL/INSTALLATION).

6. Remove in the order indicated in the table.

7. Install in the reverse order of removal.

8. After installation, inspect the parking brake stroke and adjust if necessary. (See PARKING BRAKE LEVER INSPECTION).

Mazda 2. REAR PARKING BRAKE CABLE REMOVAL/INSTALLATION

  1. Nut
  2. Front parking brake cable
  3. Rear parking brake cable

Rear Parking Brake Cable Removal Note

1. Bend the end cable tab in the direction shown in the figure.

Mazda 2. REAR PARKING BRAKE CABLE REMOVAL/INSTALLATION

2. Move the rear parking brake cable end in the direction shown in the figure and disconnect it from the end cable.

Rear Parking Brake Cable Installation Note

1. Move the rear parking brake cable end in the direction shown in the figure and install it to the end cable.

Mazda 2. REAR PARKING BRAKE CABLE REMOVAL/INSTALLATION

2. Verify that the end cable tab is attached properly to the rear parking brake cable end as shown in the figure.

END CABLE REMOVAL/INSTALLATION

1. Remove the brake shoe. (See REAR BRAKE (DRUM) REMOVAL/INSTALLATION).

2. Remove in the order indicated in the table.

3. Install in the reverse order of removal.

4. After installation, inspect the parking brake stroke and adjust if necessary. (See PARKING BRAKE LEVER INSPECTION).

Mazda 2. END CABLE REMOVAL/INSTALLATION

  1. End cable

PARKING BRAKE SWITCH INSPECTION

1. Disconnect the parking brake switch connector.

2. Verify that the continuity is as indicated in the table.

Mazda 2. PARKING BRAKE SWITCH INSPECTION

Mazda 2. PARKING BRAKE SWITCH INSPECTION

READ NEXT:

 DSC

DSC LOCATION INDEX DSC HU/CM (See DSC SYSTEM WIRING DIAGRAM.) (See DSC SYSTEM INSPECTION.) (See DSC HU/CM REMOVAL/INSTALLATION.) (See DSC HU/CM INSPECTION.) Brake fluid pressure senso

 Transmission & Transaxle

 On-Board Diagnostic System

ON-BOARD DIAGNOSTIC SYSTEM WIRING DIAGRAM NOTE: Only the transaxle-related information is described. ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION DTC Inspection Procedure (See ON-BOARD DIAGNOSTIC TES

SEE MORE:

 Manual Type

Type A Type B Type C Type D Control Switches Temperature control dial (Type A/Type B/Type C) This dial controls temperature. Turn it clockwise for hot and anticlockwise for cold. (Type D) This dial controls the air temperature when using the air conditioner. Turn it clockwise

 Fuses

Your vehicle's electrical system is protected by fuses. If any lights, accessories, or controls do not work, inspect the appropriate circuit protector. If a fuse has blown, the inside element will be melted. If the same fuse blows again, avoid using that system and consult an expert repai

© 2016-2020 Copyright www.m2info.net