Mazda 2: Manual Transaxle Shift Mechanism

Mazda 2 2007-2014 Service Manual / Transmission & Transaxle / Manual Transaxle Shift Mechanism

MANUAL TRANSAXLE SHIFT MECHANISM LOCATION INDEX

Mazda 2. MANUAL TRANSAXLE SHIFT MECHANISM LOCATION INDEX

  1. Manual transaxle shift mechanism
    • (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION)

MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION

1. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION).

2. Remove the battery and battery cover and battery tray and battery bracket. (See BATTERY REMOVAL/INSTALLATION).

3. Remove the tunnel member. (See EXHAUST SYSTEM REMOVAL/INSTALLATION).

4. Remove the TWC. (See EXHAUST SYSTEM REMOVAL/INSTALLATION).

5. Remove the exhaust system insulator as shown in the figure. (See EXHAUST SYSTEM REMOVAL/INSTALLATION).

Mazda 2. MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION

6. Remove the side wall. (See SIDE WALL REMOVAL/INSTALLATION).

7. Remove the shift lever knob as shown in the figure.

Mazda 2. MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION

8. Remove the front console component. (See FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION).

9. Remove in the order indicated in the table.

10. Install in the reverse order of removal.

11. After installation, verify that the shift lever can be shifted smoothly into each position.

Mazda 2. MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION

  1. Main shift cable end (transmission side)
  2. Main select cable end (transmission side)
  3. Seal plate
  4. Main shift cable end (shift side)
  5. Main select cable end (shift side)
  6. Shift lever component
  7. Main cable component

Main Shift Cable and Main Select Cable Removal Note

1. Remove the both shift cable end and select cable end using a fastener remover.

Mazda 2. MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION

Main Cable Component Removal Note

1. Working with two people, one person pushes the ends of the shift cable and selector cable (transaxle side) toward the inside of the vehicle, and at the same time, the other person pulls out the main cable component by pulling the ends of the shift cable and selector cable (shift lever side).

Mazda 2. MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION

Main Cable Component Installation Note

1. Working with two people, one person pushes the ends of the shift cable and selector cable (shift lever side) toward the lower side of the vehicle from the inside, and at the same time, the other person pulls the ends of the shift cable and selector cable (transaxle side), and installs the seal plate.

Mazda 2. MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION

READ NEXT:

 Automatic Transaxle

AUTOMATIC TRANSAXLE LOCATION INDEX Drive plate (See DRIVE PLATE REMOVAL/INSTALLATION) Input/turbine speed sensor (See INPUT/TURBINE SPEED SENSOR INSPECTION) (See INPUT/TURBINE SPEED SENS

 Mechanical System Test

Mechanical System Test Preparation 1. Engage the parking brake and use wheel chocks at the front and rear of the wheels. 2. Inspect the engine coolant. (See ENGINE COOLANT LEVEL INSPECTION). 3. Ins

 Road Test

WARNING: When performing a road test, be aware of other vehicles, people, impediments, etc. to avoid an accident. NOTE: When the legal speed limit must be exceeded, use a chassis dynamometer.

SEE MORE:

 Message Indicated on Display

If a message is displayed in the centre display (Type C/Type D audio), take appropriate action (in a calm manner) according to the displayed message. Stop Vehicle in Safe Place Immediately If the following messages are displayed in the centre display (Type C/Type D audio), a vehicle syst

 Fuel Pump Unit

FUEL PUMP UNIT REMOVAL/INSTALLATION WARNING: Fuel is very flammable liquid. If fuel spills or leaks from the pressurized fuel system, it will cause serious injury or death and facility breakage. Fuel can also irritate skin and eyes. To prevent this, always complete the "Fuel Line Safety Proc

© 2016-2020 Copyright www.m2info.net