Mazda 2: Lubrication System

LUBRICATION SYSTEM LOCATION INDEX

Mazda 2. LUBRICATION SYSTEM LOCATION INDEX

  1. Dipstick
    • (See ENGINE OIL LEVEL INSPECTION)
    • (See ENGINE OIL REPLACEMENT)
  2. Oil pressure switch
    • (See OIL PRESSURE INSPECTION)
  3. Oil filter
    • (See OIL FILTER REPLACEMENT)
  4. Oil strainer
    • (See OIL PAN REMOVAL/INSTALLATION)
  5. Oil pan
    • (See OIL PAN REMOVAL/INSTALLATION)
  6. Oil pump
    • (See OIL PUMP REMOVAL/INSTALLATION)
    • (See OIL PUMP DISASSEMBLY/ASSEMBLY)
    • (See OIL PUMP INSPECTION)

ENGINE OIL LEVEL INSPECTION

1. Position the vehicle on level ground.

2. Warm up the engine.

3. Stop the engine and allow at least 5 min before continuing.

4. Remove the dipstick, wipe it cleanly, and reinstall it fully.

5. Remove the dipstick and verify that the oil level is between the F and L marks on the dipstick.

Mazda 2. ENGINE OIL

ENGINE OIL REPLACEMENT

WARNING:

CAUTION:

1. Position the vehicle on level ground.

2. Remove the oil filler cap.

3. Remove the oil pan drain plug.

4. Drain the engine oil into a container.

5. Install the oil pan drain plug with a new gasket.

Oil pan drain plug tightening torque

NOTE:

6. Refill with the following type and amount of the engine oil. Engine oil specification

Engine oil grade :Mazda 2. ENGINE OIL

Engine oil viscosity :  0W-20

Engine oil capacity (approx. quantity)

7. Install the oil filler cap.

8. Start the engine and confirm that there is no oil leakage.

If there is oil leakage, repair or replace the applicable part.

9. Inspect the oil level. (See ENGINE OIL LEVEL INSPECTION).

OIL FILTER REPLACEMENT

WARNING:

CAUTION:

1. Remove the oil filter using the SST or commercially available, cup-type oil filter wrench (67 mm {2.6 in} diameter, 14 sided).

Mazda 2. OIL FILTER REPLACEMENT

2. Use a clean rag to wipe off the mounting surface on the cylinder block.

3. Apply clean engine oil to the O-ring of a new oil filter.

4. If the oil filter joint is loose, tighten it to the following torque.

Tightening torque

5. Tighten the oil filter according to the instruction on the package or side of the oil filter.

NOTE:

Tightening torque

Angle tightening

When the O-ring contacts the oil filter installation surface, turn the filter another one rotation.

6. Start the engine and confirm that there is no oil leakage.

7. Inspect the oil level. (See ENGINE OIL LEVEL INSPECTION).

OIL PRESSURE INSPECTION

WARNING:

1. Disconnect the negative battery cable.

2. Remove the oil pressure switch.

NOTE:

Mazda 2. OIL PRESSURE INSPECTION

Mazda 2. OIL PRESSURE INSPECTION

3. Install the SSTs to the oil pressure switch installation hole using the following procedure.

Using SST 49 0187 280A

Using SSTs 49 D019 908, 49 D019 909, 49 D019 910, 49 D019 911, and 49 D019 913

4. Connect the negative battery cable.

5. Warm up the engine to normal operating temperature.

6. Run the engine at the specified speed, and note the gauge readings.

NOTE:

Oil pressure (reference value) [oil temperature: 100

    READ NEXT:

     Cooling System

    COOLING SYSTEM LOCATION INDEX Cooling system cap (See COOLING SYSTEM CAP INSPECTION) Cooling fan motor (See COOLING FAN MOTOR REMOVAL/INSTALLATION) (See COOLING FAN MOTOR INSPECTION)

     Intake-air System

    INTAKE-AIR SYSTEM LOCATION INDEX Air cleaner (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION) (SeeAIR CLEANER ELEMENT INSPECTION) Variable tumble shutter valve actuator (See VARIABLE TUMBLE

     Fuel System

    FUEL SYSTEM LOCATION INDEX Engine Compartment Side Fuel distributor (See FUEL INJECTOR REMOVAL/INSTALLATION) Quick release connector (See QUICK RELEASE CONNECTOR REMOVAL/INSTALLATION)

    SEE MORE:

     Storage Compartments

    WARNING Keep storage boxes closed when driving: Driving with the storage boxes open is dangerous. To reduce the possibility of injury in an accident or a sudden stop, keep the storage boxes closed when driving. Do not put articles in storage spaces with no lid: Putting articles in storag

     Floor Mat

    WARNING Make sure the fl oor mats are secured with the grommets or the retainers to prevent them from bunching up under the foot pedals (Driver's side): Using a fl oor mat that is not secured is dangerous as it will interfere with the accelerator and brake pedal operation (driver's side), wh

    © 2016-2020 Copyright www.m2info.net