Mazda 2: Liftgate Latch and Lock Actuator

LIFTGATE LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Remove the liftgate lower trim. (See LIFTGATE LOWER TRIM REMOVAL/INSTALLATION)

3. Disconnect the connector.

Mazda 2. LIFTGATE LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION

4. Remove the bolts.

Mazda 2. LIFTGATE LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION

5. Remove the liftgate latch and lock actuator.

6. Install in the reverse order of removal.

LIFTGATE LATCH AND LOCK ACTUATOR INSPECTION

1. The following actuator and switch are integrated with the liftgate latch and lock actuator.

Inspect the liftgate latch and lock actuator according to each inspection procedure for the following items.

Mazda 2. LIFTGATE LATCH AND LOCK ACTUATOR INSPECTION

LIFTGATE LOCK ACTUATOR INSPECTION

1. Disconnect the negative battery cable.

2. Remove the liftgate lower trim. (See LIFTGATE LOWER TRIM REMOVAL/INSTALLATION).

3. Remove the liftgate latch and lock actuator. (See LIFTGATE LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION).

4. Press the latch in using a flathead screwdriver to inspect the latch lever condition.

Mazda 2. LIFTGATE LOCK ACTUATOR INSPECTION

5. Apply battery positive voltage and connect the ground to each terminal, and then verify the operation.

Mazda 2. LIFTGATE LOCK ACTUATOR INSPECTION

LIFTGATE LATCH SWITCH INSPECTION

1. Disconnect the negative battery cable.

2. Remove the liftgate lower trim. (See LIFTGATE LOWER TRIM REMOVAL/INSTALLATION).

3. Remove the liftgate latch and lock actuator. (See LIFTGATE LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION).

4. Press the latch in using a flathead screwdriver to inspect the latch lever condition.

Mazda 2. LIFTGATE LATCH SWITCH INSPECTION

5. Verify that the continuity is as indicated in the table.

Mazda 2. LIFTGATE LATCH SWITCH INSPECTION

Mazda 2. LIFTGATE LATCH SWITCH INSPECTION

LIFTGATE LOCK STRIKER REMOVAL/INSTALLATION

1. Remove the trunk end trim. (See TRUNK END TRIM REMOVAL/INSTALLATION).

2. Remove the bolts, then remove the liftgate lock striker.

Mazda 2. LIFTGATE LOCK STRIKER REMOVAL/INSTALLATION

3. Install in the reverse order of removal.

4. Adjust the liftgate lock striker. (See LIFTGATE ADJUSTMENT).

READ NEXT:

 Keyless Receiver

KEYLESS RECEIVER REMOVAL/INSTALLATION [KEYLESS ENTRY SYSTEM] 1. Disconnect the negative battery cable. 2. Remove the glove compartment. (See GLOVE COMPARTMENT REMOVAL/INSTALLATION). 3. Remove in the

 Coil Antenna

COIL ANTENNA REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the column cover. (See COLUMN COVER REMOVAL/INSTALLATION). 3. Disconnect the coil antenna connector. 4. Detach

 Exterior Trim

EXTERIOR TRIM LOCATION INDEX Cowl grille Sail garnish Roof molding Front beltline molding Splash shield Side step molding Mudguard Rear spoiler Rear door garnish Rear beltline molding Do

SEE MORE:

 Lane Departure Warning System (LDWS)

The LDWS system notifi es the driver that the vehicle may be deviating from its lane. The system detects the white or yellow lines on the traffi c lane using the forward sensing camera and if it determines that the vehicle may be deviating from its lane, it notifi es the driver using the

 Exterior Trim

EXTERIOR TRIM LOCATION INDEX Cowl grille Sail garnish Roof molding Front beltline molding Splash shield Side step molding Mudguard Rear spoiler Rear door garnish Rear beltline molding Door sash film Extractor chamber COWL GRILLE REMOVAL/INSTALLATION 1. Remove the windshield wiper arm

© 2016-2021 Copyright www.m2info.net