Mazda 2: Keyless Receiver

KEYLESS RECEIVER REMOVAL/INSTALLATION [KEYLESS ENTRY SYSTEM]

1. Disconnect the negative battery cable.

2. Remove the glove compartment. (See GLOVE COMPARTMENT REMOVAL/INSTALLATION).

3. Remove in the order indicated in the table.

Mazda 2. KEYLESS RECEIVER REMOVAL/INSTALLATION [KEYLESS ENTRY SYSTEM]

  1. Connector
  2. Nut
  3. Keyless receiver

4. Install in the reverse order of removal.

KEYLESS RECEIVER INSPECTION [KEYLESS ENTRY SYSTEM]

1. Remove the glove compartment. (See GLOVE COMPARTMENT REMOVAL/INSTALLATION).

2. Measure the voltage according to the terminal voltage table.

3. Disconnect the negative battery cable.

Terminal voltage table (reference)

Mazda 2. KEYLESS RECEIVER INSPECTION [KEYLESS ENTRY SYSTEM]

Mazda 2. KEYLESS RECEIVER INSPECTION [KEYLESS ENTRY SYSTEM]

Mazda 2. KEYLESS RECEIVER INSPECTION [KEYLESS ENTRY SYSTEM]

TRANSMITTER BATTERY REPLACEMENT [KEYLESS ENTRY SYSTEM]

1. Insert a flathead screwdriver into the transmitter notch and remove the key from the transmitter by pressing the tab.

Mazda 2. TRANSMITTER BATTERY REPLACEMENT [KEYLESS ENTRY SYSTEM]

2. Insert a flathead screwdriver into the transmitter notch and open the transmitter.

Mazda 2. TRANSMITTER BATTERY REPLACEMENT [KEYLESS ENTRY SYSTEM]

3. Remove the battery by pressing it in the direction of the arrow shown in the figure.

Mazda 2. TRANSMITTER BATTERY REPLACEMENT [KEYLESS ENTRY SYSTEM]

4. Install the new battery (CR1620) with the plus pole facing down.

Mazda 2. TRANSMITTER BATTERY REPLACEMENT [KEYLESS ENTRY SYSTEM]

5. Align the upper and lower covers and close the transmitter.

Battery type

Battery life

6. Install the key to the transmitter.

NOTE:

Mazda 2. TRANSMITTER BATTERY REPLACEMENT [KEYLESS ENTRY SYSTEM]

TRANSMITTER ID CODE REGISTRATION [KEYLESS ENTRY SYSTEM]

NOTE:

Mazda 2. TRANSMITTER ID CODE REGISTRATION [KEYLESS ENTRY SYSTEM]

Mazda 2. TRANSMITTER ID CODE REGISTRATION [KEYLESS ENTRY SYSTEM]

IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING [KEYLESS ENTRY SYSTEM]

Foreword

CAUTION:

NOTE:

Selection of Procedure for Immobilizer System-Related Parts Programming

1. Verify that the room fuse is equipped.

2. Select applicable programming procedure from the service content of the immobilizer system-related parts.

Immobilizer System-Related Parts Service and Programming Procedure Table

Mazda 2. Immobilizer System-Related Parts Service and Programming Procedure Table

Mazda 2. Immobilizer System-Related Parts Service and Programming Procedure Table

M-MDS Connecting Procedure

NOTE:

1. Fully lower the door glass.

2. Connect the M-MDS to the DLC-2.

3. Place the M-MDS outside the vehicle.

CAUTION:

No.1 Additional Key Programming Procedure (Using Two Valid Keys)

Conditions

NOTE:

Procedure

Mazda 2. Procedure

Mazda 2. Procedure

No. 2 Additional Key Programming Procedure (Using the M-MDS)

Conditions

NOTE:

Procedure

Mazda 2. Procedure

Mazda 2. Procedure

Mazda 2. Procedure

No.3 Additional Key Programming Procedure Changing

NOTE:

Procedure

Mazda 2. Procedure

No.4 Programming Procedure Due to PCM Replacement

Conditions

Procedure

Mazda 2. Procedure

Mazda 2. Procedure

No.5 Programming Procedure Due to Instrument Cluster Replacement

NOTE:

Conditions

Procedure

Mazda 2. Procedure

Mazda 2. Procedure

Mazda 2. Procedure

No.6 Programming Procedure Due to Simultaneous Replacement of Immobilizer System-related Parts (PCM and Instrument Cluster)

NOTE:

Conditions

Procedure

Mazda 2. Procedure

Mazda 2. Procedure

Mazda 2. Procedure

READ NEXT:

 Coil Antenna

COIL ANTENNA REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the column cover. (See COLUMN COVER REMOVAL/INSTALLATION). 3. Disconnect the coil antenna connector. 4. Detach

 Exterior Trim

EXTERIOR TRIM LOCATION INDEX Cowl grille Sail garnish Roof molding Front beltline molding Splash shield Side step molding Mudguard Rear spoiler Rear door garnish Rear beltline molding Do

 Interior Trim

INTERIOR TRIM LOCATION INDEX Inner garnish Meter hood Ventilator grille Dashboard Dashboard under cover Glove compartment Lower panel Knee bolster Front side trim Headliner Trunk side

SEE MORE:

 Recording of Vehicle Data

This vehicle is equipped with a computer which records the following main vehicle data related to vehicle controls, operation, and other driving conditions. Recorded data Vehicle conditions such as engine speed and vehicle speed Driving operation conditions such as accelerator and brake pe

 DTC Table [Instrument Cluster]

*1 Vehicles with tire pressure monitoring system *2 ATX DTC B1A84:41/U0300:00 Diagnostic Procedure DTC B1A84:51/U2100:00 Diagnostic Procedure DTC P0070:14 System Wiring Diagram Diagnostic Procedure DTC U0401:68 Diagnostic Procedure DTC U0401:92 Diagnostic Procedure DTC U0402:92 D

© 2016-2021 Copyright www.m2info.net