Mazda 2: Interior Care

WARNING

Do not spray water in the cabin: Splashing water on electrical parts such as the audio unit and switches is dangerous as it could cause a malfunction or a fire.

Instrument panel Precautions

Prevent caustic solutions such as perfume and cosmetic oils from contacting the instrument panel. They will damage and discolour the instrument panel. If these solutions get on the instrument panel, wipe them off immediately.

CAUTION

Do not use glazing agents.

Glazing agents contain ingredients which may cause discolouration, wrinkling, cracks and peeling.

Instrument panel top

Cleaning the Upholstery and Interior Trim

Vinyl

Remove dust and loose dirt from vinyl with a whisk broom or vacuum cleaner.

Clean vinyl with a leather-and-vinyl cleaner.

Leather *

Remove dust and sand fi rst using a vacuum cleaner or other means, then wipe dirt off using a soft cloth with a leather cleaner or a soft cloth soaked in mild soap.

Wipe off the remaining cleaner or soap using a cloth soaked in clean water and wrung out well.

Remove moisture with a dry, soft cloth and allow the leather to further dry in a well-ventilated, shaded area. If the leather gets wet such as from rain, also remove moisture and dry it as soon as possible.

NOTE

Fabric

Remove dust and loose dirt from fabric with a whisk broom or vacuum cleaner.

Clean it with a mild soap solution good for upholstery and carpets. Remove fresh spots immediately with a fabric spot cleaner.

To keep the fabric looking clean and fresh, take care of it. Otherwise its colour will be affected, it can be stained easily, and its fi re-resistance may be reduced.

CAUTION

Use only recommended cleaners and procedures. Others may affect appearance and fi re-resistance.

Panel

When the interior panels needs to be cleaned, use a soft cloth soaked in clean water and wrung out well and lightly wipe off dirt from the surface. If a panel requires further cleaning, use the following procedure.

  1. Wipe dirt off using a soft cloth soaked in mild detergent (about 5% solution).
  2. Wipe off any remaining detergent using a cloth soaked in clean water and wrung out well.

NOTE

Maintenance of the Active Driving Display

The combiner and mirror surface have a special coating. When cleaning, do not use a hard or rough-surface cloth, or cleaning detergent. In addition, if a chemical solvent gets on the active driving display, wipe it off immediately. Otherwise, the combiner and mirror could be damaged and the surface coating could be scratched.

Use a fi ne, soft cloth such as those used for cleaning eyeglasses.

Cleaning the Lap/Shoulder Belt Webbing

Clean the webbing with a mild soap solution recommended for upholstery or carpets. Follow instructions. Do not bleach or dye the webbing; this may weaken it.

After cleaning the belts, thoroughly dry the belt webbing and make sure there is no remaining moisture before retracting them.

WARNING

Have an expert repairer, we recommend an Authorised Mazda Repairer replace damaged seat belts immediately: Using damaged seat belts is dangerous.

In a collision, damaged belts cannot provide adequate protection.

Cleaning the Window Interiors

If the windows become covered with an oily, greasy, or waxy fi lm, clean them with glass cleaner. Follow the directions on the container.

CAUTION

READ NEXT:

 If Trouble Arises

Helpful information on what to do if a problem arises with the vehicle.

 Parking in an Emergency

Parking in an Emergency The hazard warning lights should always be used when you stop on or near a roadway in an emergency. The hazard warning lights warn other drivers that your vehicle is

 Flat Tyre

SEE MORE:

 Crankshaft Position (CKP) Sensor

CRANKSHAFT POSITION (CKP) SENSOR REMOVAL/INSTALLATION CAUTION: When replacing the CKP sensor, make sure there is no foreign material on it such as metal shavings. If it is installed with foreign material, the sensor output signal will malfunction resulting from fluctuation in magnetic flux a

 Blind Spot Monitoring (BSM) System

The Blind Spot Monitoring (BSM) system is designed to assist the driver in checking the area to the rear of the vehicle on both sides during lane changes by alerting the driver to the presence of vehicles approaching from the rear in an adjacent lane. The Blind Spot Monitoring (BSM) system

© 2016-2020 Copyright www.m2info.net