Mazda 2: Inspection of SST (Deployment Tool)

Mazda 2 2007-2014 Service Manual / Restraints / Inspection of SST (Deployment Tool)

1. Before using the SST (49 H066 002), inspect its operation.

Mazda 2. INSPECTION OF SST (DEPLOYMENT TOOL)

Inspection Procedure

1. Follow the steps below to inspect the SST (49 H066 002).

WARNING:

CAUTION:

Mazda 2. INSPECTION OF SST (DEPLOYMENT TOOL)

Mazda 2. INSPECTION OF SST (DEPLOYMENT TOOL)

Mazda 2. INSPECTION OF SST (DEPLOYMENT TOOL)

LOCATION INDEX

Mazda 2. LOCATION INDEX

  1. Rear seat belt
    • (See REAR SEAT BELT REMOVAL/INSTALLATION.)
    • (See SEAT BELT INSPECTION.)
  2. Rear buckle
    • (See REAR BUCKLE REMOVAL/INSTALLATION.)
  3. Adjuster anchor
    • (See ADJUSTER ANCHOR REMOVAL/INSTALLATION.)
  4. Front seat belt
    • (See FRONT SEAT BELT REMOVAL/INSTALLATION.)
    • (See SEAT BELT INSPECTION.)
  5. Front buckle
    • (See FRONT BUCKLE REMOVAL/INSTALLATION.)
    • (See BUCKLE SWITCH INSPECTION.)
  6. Rear center seat belt
    • (See REAR CENTER SEAT BELT REMOVAL/INSTALLATION.)
  7. Child-restraint seat anchor
    • (See CHILD-RESTRAINT SEAT ANCHOR REMOVAL/INSTALLATION.)

FRONT SEAT BELT REMOVAL/INSTALLATION

WARNING:

WARNING:

CAUTION:

1. Switch the ignition to off.

2. Disconnect the negative battery cable and wait for 1min or more.

3. Remove the front scuff plate. (See FRONT SCUFF PLATE REMOVAL/INSTALLATION).

4. Remove the rear scuff plate. (See REAR SCUFF PLATE REMOVAL/INSTALLATION).

5. Partially peel back the seaming welt.

6. Remove the B-pillar lower trim. (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION).

7. Remove the cover.

Mazda 2. FRONT SEAT BELT REMOVAL/INSTALLATION

8. Remove the bolt A.

9. Remove the bolt B.

10. Remove the front seat belt.

11. Using a flathead screwdriver, lift the locking device carefully, however do not remove it.

Mazda 2. FRONT SEAT BELT REMOVAL/INSTALLATION

12. Disconnect the pre-tensioner seat belt connector.

13. Install in the reverse order of removal.

14. Switch the ignition to ON.

15. Verify that the air bag system warning light illuminates for approx. 6 s and goes out.

ADJUSTER ANCHOR REMOVAL/INSTALLATION

WARNING:

1. Switch the ignition to off.

2. Disconnect the negative battery cable.

3. Remove the following parts:

  1. Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION).
  2. Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION).
  3. B-pillar lower trim (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION).
  4. Front seat belt upper anchor installation bolt (See FRONT SEAT BELT REMOVAL/INSTALLATION).
  5. B-pillar upper trim (See B-PILLAR UPPER TRIM REMOVAL/INSTALLATION).

4. Remove bolt.

Mazda 2. ADJUSTER ANCHOR REMOVAL/INSTALLATION

5. Rotate and remove the adjuster anchor as shown in the figure.

6. Install in the reverse order of removal.

REAR SEAT BELT REMOVAL/INSTALLATION

1. Remove the following parts:

  1. Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION).
  2. Trunk end trim (See TRUNK END TRIM REMOVAL/INSTALLATION).
  3. Rear seat back (See REAR SEAT BACK REMOVAL/INSTALLATION).
  4. Rear seat cushion (See REAR SEAT CUSHION REMOVAL/INSTALLATION).

2. Remove the rear seat belt lower anchor installation bolt.

Mazda 2. REAR SEAT BELT REMOVAL/INSTALLATION

3. Remove the trunk side trim. (See TRUNK SIDE TRIM REMOVAL/INSTALLATION).

4. Remove the C-pillar trim. (See C-PILLAR TRIM REMOVAL/INSTALLATION).

5. Remove the bolts.

Mazda 2. REAR SEAT BELT REMOVAL/INSTALLATION

6. Remove the rear seat belt.

7. Install in the reverse order of removal.

REAR CENTER SEAT BELT REMOVAL/INSTALLATION

SEAT BELT INSPECTION

Belt

1. Verify that the belt is installed properly with no twists or kinks.

2. Verify that there is no damage to the seat belt and no deformation of the metal fittings.

ELR

1. Verify that the belt can be pulled out smoothly, and that it retracts smoothly.

Mazda 2. SEAT BELT INSPECTION

2. Verify that the retractor locks when the belt is pulled quickly.

3. Remove the retractor.

4. While pulling the seat belt out, make sure that the seat belt does not lock when the retractor is tilted slowly up to 15

READ NEXT:

 Body and Accessories

 Foreword [Immobilizer System (Keyless Entry System) ]

DTCs are recorded in the PCM and instrument cluster when a malfunction is detected. The stored DTCs can be verified using the flashing pattern of the security light and M-MDS. There are some

 DTC Table [Immobilizer System (Keyless Entry System) ]

NOTE: The security light flashes or illuminates under the following conditions when the ignition is switched to off or ACC. There is a malfunction: DTC 16 or below: Flashes for approx. 1 min

SEE MORE:

 Engine Coolant Temperature (ECT) Sensor

ENGINE COOLANT TEMPERATURE (ECT) SENSOR REMOVAL/INSTALLATION WARNING: When the engine is hot, it can badly burn. Turn off the engine and wait until it is cool before removing the ECT sensor. ECT Sensor No.1 Removal/Installation 1. Disconnect the negative battery cable. 2. Drain the engine coo

 Vent Operation

Adjusting the Vents Directing airfl ow To adjust the direction of airfl ow, move the adjustment knob. NOTE When using the air conditioner under humid ambient temperature conditions, the system may blow fog from the vents. This is not a sign of trouble but a result of humid air being sudde

© 2016-2022 Copyright www.m2info.net