Mazda 2: Heat Duct Component

HEAT DUCT COMPONENT REMOVAL/INSTALLATION

Heat Duct (LH)

1. Disconnect the negative battery cable.

2. Remove the following parts:

  1. Rear console (See REAR CONSOLE REMOVAL/INSTALLATION).
  2. Shift lever knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION).
  3. Side wall (See SIDE WALL REMOVAL/INSTALLATION).
  4. Front console component (See FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION).
  5. Front scuff plate (LH) (See FRONT SCUFF PLATE REMOVAL/INSTALLATION).
  6. Front side trim (LH) (See FRONT SIDE TRIM REMOVAL/INSTALLATION).
  7. Hood release lever (See HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION).
  8. Driver's side lower panel (See LOWER PANEL REMOVAL/INSTALLATION).
  9. Knee bolster (See KNEE BOLSTER REMOVAL/INSTALLATION).

3. Using a flathead screwdriver, unhook the heat duct (LH) hooks and remove the heat duct (LH).

Mazda 2. HEAT DUCT COMPONENT REMOVAL/INSTALLATION

4. Install in the reverse order of removal.

Heat Duct (RH) No.1

1. Disconnect the negative battery cable.

2. Remove the following parts:

  1. Glove compartment (See GLOVE COMPARTMENT REMOVAL/INSTALLATION).
  2. Dashboard under cover (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION).

3. Remove in the order indicated in the table.

Mazda 2. HEAT DUCT COMPONENT REMOVAL/INSTALLATION

  1. Fastener
  2. Heat duct (RH) No.1

4. Install in the reverse order of removal.

Heat Duct (RH) No.2

1. Disconnect the negative battery cable.

2. Remove the following parts:

  1. Glove compartment (See GLOVE COMPARTMENT REMOVAL/INSTALLATION).
  2. Dashboard under cover (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION).
  3. Heat duct (RH) No.1
  4. Rear console (See REAR CONSOLE REMOVAL/INSTALLATION).
  5. Shift lever knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION).
  6. Side wall (See SIDE WALL REMOVAL/INSTALLATION).
  7. Front console component (See FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION).
  8. Front scuff plate (RH) (See FRONT SCUFF PLATE REMOVAL/INSTALLATION).
  9. Front side trim (RH) (See FRONT SIDE TRIM REMOVAL/INSTALLATION).
  10. Passenger's side lower panel (See LOWER PANEL REMOVAL/INSTALLATION).

3. Using a flathead screwdriver, unhook the heat duct (RH) hooks and remove the heat duct (RH) No.2.

Mazda 2. HEAT DUCT COMPONENT REMOVAL/INSTALLATION

4. Install in the reverse order of removal.

READ NEXT:

 A/C Compressor

A/C COMPRESSOR REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the splash shield (RH). 3. Collect the refrigerant. (See REFRIGERANT CHARGING). 4. Remove the drive belt. (Se

 Condenser

CONDENSER REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Collect the refrigerant. (See REFRIGERANT CHARGING). 3. Drain the engine coolant. (See ENGINE COOLANT REPLACEMENT] ). 4.

 Refrigerant Line

REFRIGERANT LINE REMOVAL/INSTALLATION 1. Remove the battery. (See BATTERY REMOVAL/INSTALLATION] ). 2. Collect the refrigerant. (See REFRIGERANT CHARGING). 3. Remove the ground from the engine mount

SEE MORE:

 Door Locks

WARNING Always take all children and pets with you or leave a responsible person with them: Leaving a child or a pet unattended in a parked vehicle is dangerous. In hot weather, temperatures inside a vehicle can become high enough to cause brain damage or even death. Do not leave the key

 DTC B1128:11/B1128:12/B1128:13/B1128:19/B1128:1A

System Malfunction Location Detection Condition WARNING: Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When p

© 2016-2021 Copyright www.m2info.net