Mazda 2: Fuel-filler Lid Opener Cable
FUEL-FILLER LID OPENER CABLE REMOVAL/INSTALLATION
1. Disconnect the negative battery cable.
2. Remove the following parts:
- Front seat (driver's seat) (See FRONT SEAT REMOVAL/INSTALLATION).
- Front scuff plate (driver's side) (See FRONT SCUFF PLATE
REMOVAL/INSTALLATION).
- Rear scuff plate (LH) (See REAR SCUFF PLATE REMOVAL/INSTALLATION).
- Rear seat back (See REAR SEAT BACK REMOVAL/INSTALLATION).
- Rear seat cushion (See REAR SEAT CUSHION REMOVAL/INSTALLATION).
- Trunk end trim (See TRUNK END TRIM REMOVAL/INSTALLATION).
- Trunk side trim (LH) (See TRUNK SIDE TRIM REMOVAL/INSTALLATION).
3. Open the fuel-filler lid opener cable cover.

4. Disconnect the fuel-filler lid opener cable from the fuel-filler lid
opener cable cover.

5. Flip over the floor mat and remove the cable from the fuel-filler lid
opener lever.

6. Remove the fuel-filler lid opener cable.

7. Install in the reverse order of removal.
FUEL-FILLER LID OPENER AND LEVER REMOVAL/INSTALLATION
Fuel-filler Lid Opener
1. Open the fuel-filler lid.
2. Remove the following parts:
- Rear scuff plate (LH) (See REAR SCUFF PLATE REMOVAL/INSTALLATION).
- Rear seat cushion (See REAR SEAT CUSHION REMOVAL/INSTALLATION).
- Rear seat back (See REAR SEAT BACK REMOVAL/INSTALLATION).
- Trunk end trim (See TRUNK END TRIM REMOVAL/INSTALLATION).
- Trunk side trim (LH) (See TRUNK SIDE TRIM REMOVAL/INSTALLATION).
3. Open the fuel-filler lid opener cable cover.

4. Disconnect the release cable from the fuel-filler lid opener cable cover.

5. Rotate the fuel-filler lid opener in the direction of the arrow (1) as
shown in the figure and
pull it out in the direction of the arrow (2).

6. Pull the lift spring in the direction of arrow (1) shown in the figure to
remove it from the tab.
7. While keeping the lift spring in the condition of Step 6, rotate the lift
spring in the direction of
arrow (2) shown in the figure to remove it.

8. Install in the reverse order of removal.
Fuel-filler Lid Opener Lever
1. Remove the front scuff plate. (Driver's side) (See FRONT SCUFF PLATE
REMOVAL/INSTALLATION).
2. Remove the front side trim. (Driver's side) (See FRONT SIDE TRIM
REMOVAL/INSTALLATION).
3. Partially peel back the floor covering.

4. Remove the bolts.

5. Disconnect the cable and fuel-filler lid opener lever.
6. Install in the reverse order of removal.
READ NEXT:
FRONT DOOR KEY CYLINDER REMOVAL/INSTALLATION
1. To access the glass installation bolt, position the front door glass so
that the distance from
the top of the front door glass to the upper part of the
FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION
1. To access the glass installation bolt, position the front door glass so
that the distance from
the top of the front door glass to the upper
FRONT DOOR LATCH SWITCH INSPECTION
1. To access the glass installation bolt, position the front door glass so
that the distance from the top of the front door glass to
the upper part of the front bel
SEE MORE:
WARNING
Make sure the fl oor mats are secured
with the grommets or the retainers to
prevent them from bunching up under
the foot pedals (Driver's side):
Using a fl oor mat that is not secured is
dangerous as it will interfere with the
accelerator and brake pedal operation
(driver's side), wh
Jacking Positions
WARNING:
Improperly jacking a vehicle is dangerous. The vehicle can slip off the
jack and cause serious injury. Use only the correct front and rear
jacking points and block the wheels.
Use safety stands to support the vehicle after it has been lifted.
Front
NOTE:
To preven
© 2016-2022 Copyright www.m2info.net
