Mazda 2: Front Door Latch and Lock Actuator

FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION

1. To access the glass installation bolt, position the front door glass so that the distance from the top of the front door glass to the upper part of the front beltline molding is approx. 110 mm {4.33 in}.

Mazda 2. FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION

2. Disconnect the negative battery cable.

3. Remove the following parts:

  1. Inner garnish (See INNER GARNISH REMOVAL/INSTALLATION).
  2. Front door trim (See FRONT DOOR TRIM REMOVAL/INSTALLATION).
  3. Front inner handle (See DOOR LOCK-LINK SWITCH INSPECTION).
  4. Front door speaker (See FRONT DOOR SPEAKER REMOVAL/INSTALLATION).
  5. Front door glass (See FRONT DOOR GLASS REMOVAL/INSTALLATION).
  6. Front door module panel (See FRONT DOOR MODULE PANEL REMOVAL/INSTALLATION).
  7. Rod protector (See FRONT DOOR KEY CYLINDER REMOVAL/INSTALLATION).

4. Lift the clip in the direction of the arrow (1), and pull out the key rod in the direction of the arrow (2).

Mazda 2. FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION

5. Remove the screw

Mazda 2. FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION

6. Detach the clips.

7. Press down the rod holder of the front door latch and lock actuator in the direction of the arrow.

Mazda 2. FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION

8. Maintaining the condition in procedure 7, remove the front door latch and lock actuator.

Mazda 2. FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION

9. Install in the reverse order of removal.

FRONT DOOR LATCH AND LOCK ACTUATOR INSPECTION

1. The following actuators and switches are integrated with the front door latch and lock actuator. Inspect the front door latch and lock actuator according to each inspection procedure for the following items.

LH

Mazda 2. FRONT DOOR LATCH AND LOCK ACTUATOR INSPECTION

RH

Mazda 2. FRONT DOOR LATCH AND LOCK ACTUATOR INSPECTION

FRONT DOOR LOCK ACTUATOR INSPECTION

1. To access the glass installation bolt, position the front door glass so that the distance from the top of the front door glass to the upper part of the front beltline molding is approx. 110 mm {4.33 in}.

Mazda 2. FRONT DOOR LOCK ACTUATOR INSPECTION

2. Disconnect the negative battery cable.

3. Remove the following parts:

  1. Inner garnish (See INNER GARNISH REMOVAL/INSTALLATION).
  2. Front door trim (See FRONT DOOR TRIM REMOVAL/INSTALLATION).
  3. Front door speaker (See FRONT DOOR SPEAKER REMOVAL/INSTALLATION).
  4. Front door glass (See FRONT DOOR GLASS REMOVAL/INSTALLATION).
  5. Front door module panel (See FRONT DOOR MODULE PANEL REMOVAL/INSTALLATION).
  6. Front door latch and lock actuator (See FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION).

4. Apply battery positive voltage and connect the ground to each terminal, and then verify the operation.

Mazda 2. FRONT DOOR LOCK ACTUATOR INSPECTION

READ NEXT:

 Front Door Latch Switch

FRONT DOOR LATCH SWITCH INSPECTION 1. To access the glass installation bolt, position the front door glass so that the distance from the top of the front door glass to the upper part of the front bel

 Rear Door Latch and Lock Actuator

REAR DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION 1. To access the glass installation bolt, position the rear door glass so that the distance from the top of the rear door glass to the upper par

 Liftgate Latch and Lock Actuator

LIFTGATE LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the liftgate lower trim. (See LIFTGATE LOWER TRIM REMOVAL/INSTALLATION) 3. Disconnect the

SEE MORE:

 Manual Transaxle Shift Mechanism

MANUAL TRANSAXLE SHIFT MECHANISM LOCATION INDEX Manual transaxle shift mechanism (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION) MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION). 2. Remove the ba

 Mechanical System Test

Mechanical System Test Preparation 1. Engage the parking brake and use wheel chocks at the front and rear of the wheels. 2. Inspect the engine coolant. (See ENGINE COOLANT LEVEL INSPECTION). 3. Inspect the engine oil. (See ENGINE OIL LEVEL INSPECTION). 4. Inspect the ATF. (See AUTOMATIC TRANSAXL

© 2016-2022 Copyright www.m2info.net