Mazda 2: Front Console Component

FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION

1. Shift lever to neutral position.

2. Remove the following parts:

  1. Rear console (See REAR CONSOLE REMOVAL/INSTALLATION).
  2. Side wall (See SIDE WALL REMOVAL/INSTALLATION).
  3. Shift lever knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION).

3. Remove the screws, then pull the lower side of the front console component in the direction of the arrow, and remove the clips.

CAUTION:

4. Install the boot panel and front console as a single unit.

5. Install in the reverse order of removal.

FRONT CONSOLE COMPONENT DISASSEMBLY/ASSEMBLY

ATX

1. Disassemble in the order indicated in the table.

  1. Boot panel
  2. Front console

2. Assemble in the reverse order of disassembly.

MTX

1. Disassemble in the order indicated in the table.

  1. Boot panel
  2. Screw
  3. Set panel
  4. Boot
  5. Front console

2. Assemble in the reverse order of disassembly.

REAR CONSOLE REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Pull the console panel in the direction of the arrow (1), (2) shown in the figure and remove it while detaching hooks A, tab B, and the hooks C.

3. Disconnect the auxiliary jack connector and door lock switch connector (vehicles with auxiliary jack).

4. Remove nut D, then remove the clip F.

5. Pull up the rear console in the direction of the arrow (3) shown in the figure, remove clips G, move the rear console in the direction of the arrow (4), and remove it avoiding the parking brake lever.

CAUTION:

6. Install in the reverse order of removal.

A-PILLAR TRIM REMOVAL/INSTALLATION

1. Partially peel back the seaming welt.

2. Pull the upper end of the A-pillar trim in the direction of the arrow shown in the figure and remove clips A and B.

3. Cut the lead wire connecting clip B and grommet using a nipper and pull out the A-pillar trim in the direction of the arrow shown in the figure.

CAUTION:

4. Move the hook in the direction of arrows (1) and (2) shown in the figure using a flathead screwdriver and detach it from the A-pillar inner panel.

5. Remove the grommet in the direction of the arrow (3) shown in the figure.

6. When installing the A-pillar trim, install the new clip B and grommet to the A-pillar trim in advance.

7. Install in the reverse order of removal.

B-PILLAR UPPER TRIM REMOVAL/INSTALLATION

1. Remove the following parts:

  1. Adjuster anchor cover (See FRONT SEAT BELT REMOVAL/INSTALLATION).
  2. Upper anchor installation bolts of the front seat belt (See FRONT SEAT BELT REMOVAL/INSTALLATION).
  3. Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION).
  4. Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION).

2. Partially peel back the seaming welt.

3. Remove the B-pillar lower trim. (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION).

4. Grasp the lower end of the B-pillar upper trim, pull it in the direction of the arrow shown in the figure, and remove hooks A, guide pin B, pins C, and clip D.

5. Remove the B-pillar upper trim in the direction of the arrow shown in the figure.

CAUTION:

6. If there is a remaining clip D, rotate it 90

READ NEXT:

 Front Door Trim

FRONT DOOR TRIM REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the inner garnish. (See INNER GARNISH REMOVAL/INSTALLATION) 3. Pull the cover of inner handle while remove the

 Rear Door Trim

REAR DOOR TRIM REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the sail inner garnish. (See SAIL INNER GARNISH REMOVAL/INSTALLATION) 3. Pull the cover of inner handle while r

 Lighting Systems

LIGHTING SYSTEMS LOCATION INDEX Back-up light switch Front combination light Auto light sensor Side turn light Front fog light Cargo compartment light Rear combination light High-mount brak

SEE MORE:

 Front Door Key Cylinder

FRONT DOOR KEY CYLINDER REMOVAL/INSTALLATION 1. To access the glass installation bolt, position the front door glass so that the distance from the top of the front door glass to the upper part of the front beltline molding is approx. 110 mm {4.33 in}. 2. Disconnect the negative battery cable. 3

 Rear Door Trim

REAR DOOR TRIM REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the sail inner garnish. (See SAIL INNER GARNISH REMOVAL/INSTALLATION) 3. Pull the cover of inner handle while remove the tabs. 4. Remove the screw. 5. Pull in the direction of the arrow shown in the figure and

© 2016-2021 Copyright www.m2info.net