Mazda 2: Engine

ENGINE REMOVAL/INSTALLATION

WARNING:

NOTE:

1. Complete the "Fuel Line Safety Procedure", and remove the fuel pump relay. (See BEFORE SERVICE PRECAUTION).

2. Remove the battery and the battery tray. (See BATTERY REMOVAL/INSTALLATION).

3. Drain the engine coolant. (See ENGINE COOLANT REPLACEMENT).

4. Drain the ATF (ATX) or transaxle oil (MTX). (See AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT [FN4A-EL] (ATX) ). (See TRANSAXLE OIL REPLACEMENT [F35M-R] (MTX) ).

5. Remove the front wheels and tires (See GENERAL PROCEDURES (SUSPENSION) ).

6. Disconnect the radiator hose.

7. Remove the fresh-air duct and the air cleaner as a single unit, the evaporative hose, and the air hose. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION).

8. Disconnect the fuel hose. (See QUICK RELEASE CONNECTOR REMOVAL/INSTALLATION).

9. Remove the drive belt. (See DRIVE BELT REMOVAL/INSTALLATION).

10. Set the cooler pipe and the cooler hose (LO) out of the way. (See REFRIGERANT LINE REMOVAL/INSTALLATION).

11. Remove the generator. (See GENERATOR REMOVAL/INSTALLATION).

NOTE:

12. Remove the A/C compressor with the pipes still connected. (See A/C COMPRESSOR REMOVAL/INSTALLATION).

13. Disconnect the front drive shafts. (See DRIVE SHAFT REMOVAL/INSTALLATION).

14. Disconnect the selector cable, and wiring harness. (ATX) (See AUTOMATIC TRANSAXLE REMOVAL/INSTALLATION).

15. Disconnect the shift cable. (MTX) (See MANUAL TRANSAXLE REMOVAL/INSTALLATION).

16. Remove the clutch release cylinder with the pipe still connected. (MTX) (See CLUTCH RELEASE CYLINDER REMOVAL/INSTALLATION).

17. Disconnect the vacuum hose and the heater hose.

18. Disconnect the wiring harness from the engine side.

19. Remove the middle pipe or the presilencer. (See EXHAUST SYSTEM REMOVAL/INSTALLATION).

20. Remove in the order indicated in the table.

21. Install in the reverse order of removal.

22. Start the engine. and inspect and adjust the following.

NOTE:

Mazda 2. ENGINE REMOVAL/INSTALLATION

  1. No.1 Engine mount rubber
  2. Battery tray bracket
  3. No.4 Engine mount rubber
  4. No.3 Engine mount
  5. Engine, transaxle

No.1 Engine Mount Removal Note

1. Remove the No.1 engine mount installation bolt (A) from below the vehicle.

Mazda 2. ENGINE REMOVAL/INSTALLATION

2. Remove the No.1 engine mount rubber and the front crossmember as a single unit. (See FRONT CROSSMEMBER REMOVAL/INSTALLATION).

Mazda 2. ENGINE REMOVAL/INSTALLATION

No.3 Engine Mount, No.4 Engine Mount Rubber Removal Note

CAUTION:

Mazda 2. ENGINE REMOVAL/INSTALLATION

1. Secure the engine and the transaxle using an engine jack.

Mazda 2. ENGINE REMOVAL/INSTALLATION

No.3 Engine Mount, No.4 Engine Mount Rubber Installation Note

1. Secure the engine and the transaxle using an engine jack.

Mazda 2. ENGINE REMOVAL/INSTALLATION

2. Install the No.3 engine mount, and then temporarily tighten the installation bolts and nuts.

3. Tighten the installation bolts and nuts by order of A,B.

Mazda 2. ENGINE REMOVAL/INSTALLATION

Tightening torque

4. Install the No.4 engine mount rubber, and then temporarily tighten the installation bolts and nuts.

5. Tighten the installation bolts and nuts by order of A,B.

Mazda 2. ENGINE REMOVAL/INSTALLATION

Tightening torque

6. Remove the engine jack and attachment.

No.1 Engine Mount Installation Note

1. Install the front crossmember component. (See FRONT CROSSMEMBER REMOVAL/INSTALLATION).

2. Tighten the No.1 engine mount installation bolt (A).

Mazda 2. ENGINE REMOVAL/INSTALLATION

Tightening torque

Mazda 2. ENGINE REMOVAL/INSTALLATION

Tightening torque

Engine Disassembly/Assembly

1. Remove the fuel line bracket.

Mazda 2. ENGINE DISASSEMBLY/ASSEMBLY

2. Using the bolts part number 99794 1025 or M10

READ NEXT:

 Lubrication System

LUBRICATION SYSTEM LOCATION INDEX Dipstick (See ENGINE OIL LEVEL INSPECTION) (See ENGINE OIL REPLACEMENT) Oil pressure switch (See OIL PRESSURE INSPECTION) Oil filter (See OIL FIL

 Cooling System

COOLING SYSTEM LOCATION INDEX Cooling system cap (See COOLING SYSTEM CAP INSPECTION) Cooling fan motor (See COOLING FAN MOTOR REMOVAL/INSTALLATION) (See COOLING FAN MOTOR INSPECTION)

 Intake-air System

INTAKE-AIR SYSTEM LOCATION INDEX Air cleaner (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION) (SeeAIR CLEANER ELEMENT INSPECTION) Variable tumble shutter valve actuator (See VARIABLE TUMBLE

SEE MORE:

 Cruise Control

With cruise control, you can set and automatically maintain any speed of more than about 25 km/h (16 mph). WARNING Do not use the cruise control under the following conditions: Using the cruise control under the following conditions is dangerous and could result in loss of vehicle control.

 Collection/Disposal of Old Equipment/Used Battery

Information for Users on Collection and Disposal of Old Equipment and Used Batteries When disposing your old battery, please refer to the information as follows. Information on Disposal in the European Union These crossed-out wheeled bin symbols on the products, packaging, and/or accompanying

© 2016-2020 Copyright www.m2info.net