Mazda 2: DTC Table [Instrument Cluster]

Mazda 2 2007-2014 Service Manual / Body and Accessories / DTC Table [Instrument Cluster]

Mazda 2. DTC TABLE

Mazda 2. DTC TABLE

Mazda 2. DTC TABLE

*1 Vehicles with tire pressure monitoring system
*2 ATX

DTC B1A84:41/U0300:00

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

DTC B1A84:51/U2100:00

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

DTC P0070:14

Mazda 2. DTC

System Wiring Diagram

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

DTC U0401:68

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

DTC U0401:92

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

DTC U0402:92

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

DTC U0415:92

NOTE:

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

DTC U0420:92

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

DTC U0452:68

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

DTC U0452:92

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

DTC U2005:86

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

DTC U3000:41

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

DTC U3003:16

Mazda 2. DTC

System Wiring Diagram

Mazda 2. DTC

Diagnostic Procedure

Mazda 2. DTC

Mazda 2. DTC

Mazda 2. DTC

PID/DATA MONITOR INSPECTION [Instrument Cluster]

1. Connect the M-MDS (IDS) to the DLC-2.

2. After the vehicle is identified, select the following items from the initialization screen of the IDS.

  1. Select "DataLogger".
  2. Select "Modules".
  3. Select "IC".

3. Select the applicable PID from the PID table.

4. Verify the PID data according to the directions on the screen.

NOTE:

PID/DATA MONITOR TABLE [Instrument Cluster]

Mazda 2. PID/DATA MONITOR TABLE

Mazda 2. PID/DATA MONITOR TABLE

* Vehicles with tire pressure monitoring system

ACTIVE COMMAND MODES INSPECTION [Instrument Cluster]

1. Connect the M-MDS (IDS) to the DLC-2.

2. After the vehicle is identified, select the following items from the initialization screen of the IDS.

  1. Select "DataLogger".
  2. Select "Modules".
  3. Select "IC".

3. Select the simulation items from the PID table.

4. Perform the active command modes function, inspect the operations for each parts.

If the operation of output parts cannot be verified after the active command mode inspection is performed, this could indicate the possibility of an open or short circuit, sticking, or operation malfunction in the output parts.

ACTIVE COMMAND MODES TABLE [Instrument Cluster]

Mazda 2. ACTIVE COMMAND MODES TABLE

READ NEXT:

 ON-Board Diagnostic Wiring Diagram [BCM]

DTC INSPECTION [BCM] 1. Connect the M-MDS (IDS) to the DLC-2. 2. Verify the following vehicle conditions: Switch the ignition to ON. All the switches are turned off (except the ignition switch)

 DTC Table [BCM]

*1 ATX DTC B1B55:96 Diagnostic procedure DTC B1C53:13 System Wiring Diagram Diagnostic Procedure DTC B1D06:11 System Wiring Diagram Diagnostic Procedure DTC B1D06:15 System Wiring Dia

 DTC Inspection [Audio]

NOTE: All DTCs displayed in the on-board diagnostic test mode should be entered in the Audio Repair Order Form. 1. Turn the ignition switch to the ACC or ON position. 2. Turn the center panel u

SEE MORE:

 Audio Set (Type C/Type D)

NOTE The explanation of functions described in this manual may differ from the actual operation, and the shapes of screens and buttons and the letters and characters displayed may also differ from the actual appearance. Additionally, depending on future software updates, the content may succ

 Power Window System Wiring Diagram [Power Window System]

FOREWORD [POWER WINDOW SYSTEM] Troubleshooting Procedure Slightly shake the wiring harness and connectors while performing the inspection to discover whether poor contact points are the cause of any intermittent malfunctions. CAUTION: If any of the following conditions continues indefinite

© 2016-2021 Copyright www.m2info.net