Mazda 2: DTC Table [BCM]




*1 ATX
DTC B1B55:96

Diagnostic procedure


DTC B1C53:13

System Wiring Diagram

Diagnostic Procedure


DTC B1D06:11

System Wiring Diagram

Diagnostic Procedure



DTC B1D06:15

System Wiring Diagram

Diagnostic Procedure




DTC B1D07:11

System Wiring Diagram

Diagnostic Procedure



DTC B1D07:15

System Wiring Diagram

Diagnostic Procedure




DTC B1D13:12

System Wiring Diagram

Diagnostic Procedure


DTC B1D35:11

System Wiring Diagram

Diagnostic Procedure


DTC B1D36:92

System Wiring Diagram

Diagnostic Procedure



DTC B10A6:92

System Wiring Diagram

Diagnostic procedure


DTC B1008:11

System wiring diagram

Diagnostic Procedure


DTC B1013:23

System Wiring Diagram

Diagnostic Procedure


DTC B1087:83/B1087:86/B1087:87/B1087:88

System Wiring Diagram

Diagnostic procedure


DTC B1172:92

System Wiring Diagram

Diagnostic Procedure



DTC B1175:13

System Wiring Diagram

Diagnostic Procedure


DTC B1176:13

System Wiring Diagram

Diagnostic Procedure


DTC B1178:11

System Wiring Diagram

Diagnostic Procedure


DTC U0028:81/U0028:83/U0028:87

System Wiring Diagram

Diagnostic Procedure


DTC U0415:68

Diagnostic Procedure


DTC U2100:00/U3000:44

Diagnostic Procedure


DTC U3003:16/U3003:17

System Wiring Diagram

Diagnostic Procedure



PID/DATA MONITOR INSPECTION
1. Connect the M-MDS (IDS) to the DLC-2.
2. After the vehicle is identified, select the following items from the
initialization screen of
the IDS.
- Select "DataLogger".
- Select "Modules".
- Select "BCM/GEM".
3. Select the applicable PID from the PID table.
4. Verify the PID data according to the directions on the screen.
NOTE:
- The PID data screen function is used for monitoring the calculated value
of
input/output signals in the module. Therefore, if the monitored value of the
output parts
is not within the specification, it is necessary to inspect the monitored
value of input
parts corresponding to the applicable output part control. In addition,
because the
system does not display an output part malfunction as an abnormality in the
monitored
value, it is necessary to inspect the output parts individually.
PID/DATA MONITOR TABLE
![Mazda 2. PID/DATA MONITOR TABLE [BCM]](images/books/1059/mazda_2_dtc_table_bcm__2896.jpg)
![Mazda 2. PID/DATA MONITOR TABLE [BCM]](images/books/1059/mazda_2_dtc_table_bcm__2897.jpg)
![Mazda 2. PID/DATA MONITOR TABLE [BCM]](images/books/1059/mazda_2_dtc_table_bcm__2898.jpg)
READ NEXT:
NOTE:
All DTCs displayed in the on-board diagnostic test mode should be
entered in the Audio
Repair Order Form.
1. Turn the ignition switch to the ACC or ON position.
2. Turn the center panel u
NOTE:
"iPod" is a registered trademark of Apple Inc. in the United States and other
countries.
DTC: 28:Er01, 28:Er09
NOTE:
"iPod" is a registered trademark of Apple Inc. in the United States and
LCD Inspection
1. Turn the ignition switch to the ACC or ON position.
2. Turn the center panel unit power to on.
3. While pressing the POWER/VOLUME switch, simultaneously press the TUNE/TRACK
UP
sw
SEE MORE:
Troubleshooting Index
NO.1 CD PLAYER DOES NOT LOAD THE CD OR EJECTS THE CD IMMEDIATELY
Diagnostic procedure
NO.2 CD PLAYER DOES NOT EJECT THE CD
Diagnostic procedure
NO.3 CD PLAYER DOES NOT PLAY THE CD/NO SOUND
Diagnostic procedure
NO.4 SOUND JUMPS
Diagnostic procedure
NO.5 CD PLAYER
Seat belts help to decrease the possibility of severe injury during accidents
and sudden
stops. Mazda recommends that the driver and all passengers always wear seat
belts.
Front seat and rear outboard seat
The front seats and rear outboard seats have lap/shoulder belts. These belts
have ret
© 2016-2022 Copyright www.m2info.net
