Mazda 2: DTC B00A0:1C
System Malfunction Location
- Seat weight sensor control module circuit open to power supply
Detection Condition
WARNING:
- Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure.
- Malfunction in seat weight sensor control module circuit.
Possible Causes
- SWS 7.5 A fuse malfunction
- Seat weight sensor control module connector malfunction
- Open or short circuit to power supply in wiring harness between fuse block and seat weight sensor control module.
- Seat weight sensor control module malfunction
System Wiring Diagram
Diagnostic Procedure
DTC B00A0:28
System Malfunction Location
- Seat weight sensor calibration setting invalid
Detection Condition
WARNING:
- Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure.
- Calibration set value not within valid range.
Possible Causes
- Seat weight sensor deformed or malfunction
- Load to or deformation of the seat belt rail
- Deformed front passenger-side seat under-bracket or frame
- Weight acting on front passenger-side seat during calibration
- Improperly installed front passenger-side seat part at time of calibration
- Deformed floor where attached to front passenger-side seat
- Seat weight sensor control module malfunction
- SAS control module malfunction
Diagnostic Procedure
DTC B00A0:4A
System Malfunction Location
- Seat weight sensor ID mismatch
Detection Condition
WARNING:
- Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure.
- Seat weight sensor ID mismatch
Possible Causes
- Seat weight sensor control module malfunction
- SAS control module malfunction
Diagnostic Procedure
DTC B00A0:54
System Malfunction Location
- Seat weight sensor calibration setting not set
Detection Condition
WARNING:
- Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure.
- Seat weight sensor calibration setting has not been done correctly
Possible Causes
- Seat weight sensor calibration setting not implemented
- Seat weight sensor calibration setting invalid
- Seat weight sensor control module malfunction
Diagnostic Procedure
READ NEXT:
DTC B00A0:81/B00A0:87/B00A0:8F
System Malfunction Location
Detection Condition
WARNING:
Detection conditions are for understanding the DTC outline before
performing an inspection. Performing an
inspection according to only th
DTC B00B5:11/B00B5:12/B00B5:13/B00B5:1D
System Malfunction Location
Detection Condition
WARNING:
Detection conditions are for understanding the DTC outline before
performing an
inspection. Performing an inspection according to only th
DTC B00D5:11/B00D5:12
System Malfunction Location
Detection Condition
WARNING:
Detection conditions are for understanding the DTC outline before
performing an
inspection. Performing an inspection according to only th
SEE MORE:
Hill Launch Assist (HLA)
Hill Launch Assist (HLA) is a function
which assists the driver in accelerating
from a stop while on a slope. When
the driver releases the brake pedal and
depresses the accelerator pedal while
on a slope, the function prevents the
vehicle from rolling. The braking force is
maintained automati
Power Brake Unit
POWER BRAKE UNIT INSPECTION
NOTE:
The following inspection methods are simple inspection methods to judge
the function
of the power brake unit.
If there is any malfunction in the power brake unit, replace the power
brake unit as a
single component.
Without Using SST
Operation inspection
1.
© 2016-2021 Copyright www.m2info.net