Mazda 2: Door Lock Switch

DOOR LOCK SWITCH REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Remove the console panel. (See REAR CONSOLE REMOVAL/INSTALLATION).

3. Remove the screws.

Mazda 2. DOOR LOCK SWITCH REMOVAL/INSTALLATION

4. Disconnect the door lock switch connector.

5. Install in the reverse order of removal.

DOOR LOCK SWITCH INSPECTION

1. Inspect for continuity between the door lock switch terminals.

Mazda 2. DOOR LOCK SWITCH INSPECTION

Mazda 2. DOOR LOCK SWITCH INSPECTION

HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION

Hood Latch

1. Open the hood.

2. Remove the bolts.

Mazda 2. HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION

3. Remove the hood latch.

4. Install in the reverse order of removal.

5. Adjust the hood. (See HOOD ADJUSTMENT).

Hood Release Lever

1. Pull the hood release lever.

Mazda 2. HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION

2. While maintaining the condition in procedure 1, insert a tape-wrapped flathead screwdriver as shown in the figure, press the ends of the tabs with the screwdriver in the direction of the arrows (1), pull the hood release lever in the direction of arrow (2), and then disconnect the lower panel.

Mazda 2. HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION

CAUTION:

3. Pull the latch release lever outward, remove it from the lower panel, and then disconnect the hood release cable.

Mazda 2. HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION

4. Install in the reverse order of removal.

HOOD RELEASE CABLE REMOVAL/INSTALLATION

1. Disconnect the negative battery cable. (Vehicle with front fog lights)

2. Remove the front bumper. (See FRONT BUMPER REMOVAL/INSTALLATION).

3. Remove the seal board upper. (See SEAL BOARD UPPER REMOVAL/INSTALLATION).

4. Remove the hood release lever. (See HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION).

5. Remove the hood release cable from clips A.

6. Remove the clips B.

7. Disconnect the hood latch from the hood release cable.

8. Remove the hood release cable from outside of the vehicle.

Mazda 2. HOOD RELEASE CABLE REMOVAL/INSTALLATION

9. Install in the reverse order of removal.

HOOD LATCH SWITCH INSPECTION

1. Disconnect the negative battery cable.

2. Remove the hood latch. (See HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION).

3. Press the latch in using a flathead screwdriver to inspect the latch lever condition.

Mazda 2. HOOD LATCH SWITCH INSPECTION

4. Verify that the continuity is as indicated in the table.

Mazda 2. HOOD LATCH SWITCH INSPECTION

Mazda 2. HOOD LATCH SWITCH INSPECTION

READ NEXT:

 Fuel-filler Lid Opener Cable

FUEL-FILLER LID OPENER CABLE REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the following parts: Front seat (driver's seat) (See FRONT SEAT REMOVAL/INSTALLATION). Front s

 Front Door Key Cylinder

FRONT DOOR KEY CYLINDER REMOVAL/INSTALLATION 1. To access the glass installation bolt, position the front door glass so that the distance from the top of the front door glass to the upper part of the

 Front Door Latch and Lock Actuator

FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION 1. To access the glass installation bolt, position the front door glass so that the distance from the top of the front door glass to the upper

SEE MORE:

 Automatic Transaxle Control System

AUTOMATIC TRANSAXLE CONTROL SYSTEM WIRING DIAGRAM NOTE: Only the transaxle-related information is described. FOREWORD When the customer reports a vehicle malfunction, check the malfunction indicator lamp (MIL) illuminating, O/D OFF indicator light flashing, and diagnostic trouble code (DTC)

 Before/After Service

BEFORE SERVICE PRECAUTION WARNING: Fuel vapor is hazardous. It can very easily ignite, causing serious injury and damage. Always keep sparks and flames away from fuel. Fuel line spills and leakage from the pressurized fuel system are dangerous. Fuel can ignite and cause serious injury or d

© 2016-2021 Copyright www.m2info.net