Mazda 2: Control System

CONTROL SYSTEM LOCATION INDEX

Mazda 2. CONTROL SYSTEM LOCATION INDEX

  1. BCM (body control module)

BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION

CAUTION:

1. Perform the BCM configuration when replacing it. (See BODY CONTROL MODULE (BCM) CONFIGURATION).

2. Disconnect the negative battery cable.

3. Remove the dashboard under cover. (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION).

4. Remove the glove compartment. (See GLOVE COMPARTMENT REMOVAL/INSTALLATION).

5. Disconnect the connectors at the position shown in the figure.

Mazda 2. BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION

6. Remove the nuts.

Mazda 2. BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION

7. Remove the BCM.

8. Install in the reverse order of removal.

BODY CONTROL MODULE (BCM) INSPECTION

1. Remove the dashboard under cover. (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION).

2. Remove the glove compartment. (See GLOVE COMPARTMENT REMOVAL/INSTALLATION).

3. Measure the voltage at each terminal and inspect for the continuity between the terminals and ground is as indicated in the Terminal Voltage Tables (Reference).

Terminal Voltage Table (Reference)

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Mazda 2. BODY CONTROL MODULE (BCM) INSPECTION

Generated pulse (reference)

Pattern 1

Mazda 2. Generated pulse (reference)

Pattern 2

Mazda 2. Generated pulse (reference)

Pattern 3

Mazda 2. Generated pulse (reference)

Pattern 4

Mazda 2. Generated pulse (reference)

Pattern 5

Mazda 2. Generated pulse (reference)

Pattern 6

Mazda 2. Generated pulse (reference)

Pattern 7

Mazda 2. Generated pulse (reference)

Liftgate Opener Switch Input Signal Pulse (Reference)

Liftgate opener switch not pressed

Mazda 2. Liftgate Opener Switch Input Signal Pulse (Reference)

Liftgate opener switch pressed

Mazda 2. Liftgate Opener Switch Input Signal Pulse (Reference)

Liftgate Opener Switch Signal Pulse (Reference)

Mazda 2. Liftgate Opener Switch Signal Pulse (Reference)

Door lock actuators 2-step unlocking (Reference)

Mazda 2. Door lock actuators 2-step unlocking (Reference)

Sensitivity adjustment volume (Reference)

1 position

Mazda 2. Sensitivity adjustment volume (Reference)

2 position

Mazda 2. Sensitivity adjustment volume (Reference)

3 position

Mazda 2. Sensitivity adjustment volume (Reference)

4 position

Mazda 2. Sensitivity adjustment volume (Reference)

5 position

Mazda 2. Sensitivity adjustment volume (Reference)

BODY CONTROL MODULE (BCM) BRACKET REMOVAL/INSTALLATION

Removal

1. Disconnect the negative battery cable.

2. Remove the dashboard under cover. (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION).

3. Remove the glove compartment. (See GLOVE COMPARTMENT REMOVAL/INSTALLATION).

4. Remove the BCM. (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION).

5. Insert a fastener remover in the direction of the arrow (1) shown in the figure and release the tabs.

CAUTION:

Mazda 2. BODY CONTROL MODULE (BCM) BRACKET REMOVAL/INSTALLATION

6. Pull the BCM in the direction of the arrow (2) as shown in the figure and remove the BCM bracket.

Mazda 2. BODY CONTROL MODULE (BCM) BRACKET REMOVAL/INSTALLATION

Installation

1. Bend the tabs in the direction of the arrow (1) so that clearance (a) indicated in the figure is within the specification.

Mazda 2. BODY CONTROL MODULE (BCM) BRACKET REMOVAL/INSTALLATION

Clearance

2. Press the BCM in the direction of the arrow (2) as shown in the figure and install it.

Mazda 2. BODY CONTROL MODULE (BCM) BRACKET REMOVAL/INSTALLATION

3. Install the BCM. (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION).

4. Install the glove compartment. (See GLOVE COMPARTMENT REMOVAL/INSTALLATION).

5. Install the dashboard under cover. (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION).

6. Connect the negative battery cable.

BODY CONTROL MODULE (BCM) CONFIGURATION

1. Connect the M-MDS (IDS) to the DLC-2.

2. After the vehicle is identified, select the following items from the initial screen of the M-MDS.

  1. Select "Module Programming".
  2. Select "Programmable Module Installation".
  3. Select "BCM/GEM".

3. Perform the configuration according to the directions on the screen.

4. Retrieve DTCs by the M-MDS, then verify that there is no DTC present.

BODY AND ACCESSORIES TECHNICAL DATA

Mazda 2. BODY AND ACCESSORIES TECHNICAL DATA

READ NEXT:

SEE MORE:

 Windscreen Wipers and Washer

The ignition must be switched ON to use the wipers. WARNING Use only windscreen washer fl uid or plain water in the reservoir: Using radiator antifreeze as washer fl uid is dangerous. If sprayed on the windscreen, it will dirty the windscreen, affect your visibility, and could result in an

 Driving In Flooded Area

WARNING Dry off brakes that have become wet by driving slowly, releasing the accelerator pedal and lightly applying the brakes several times until the brake performance returns to normal: Driving with wet brakes is dangerous. Increased stopping distance or the vehicle pulling to one side w

© 2016-2021 Copyright www.m2info.net