Mazda 2: Clock Spring

CLOCK SPRING REMOVAL/INSTALLATION

1. Switch the ignition to off.

2. Disconnect the negative battery cable and wait for 1 min or more.

3. Remove the following parts:

  1. Driver-side air bag module (See DRIVER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION).
  2. Steering wheel (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION).
  3. Column cover (See COLUMN COVER REMOVAL/INSTALLATION).

4. Disconnect the clock spring connector.

Mazda 2. CLOCK SPRING REMOVAL/INSTALLATION

5. Press and detach the tab of the clock spring in the direction of the arrow of the clock spring in the position shown in the figure.

6. Insert a flathead screwdriver into the service hole of the combination switch in the position shown in the figure, and detach the tab of the clock spring.

Mazda 2. CLOCK SPRING REMOVAL/INSTALLATION

7. Remove the clock spring.

8. Install in the reverse order of removal.

CAUTION:

9. Perform the clock spring adjustment. (See CLOCK SPRING ADJUSTMENT).

10. Switch the ignition to ON.

11. Verify that the air bag system warning light illuminates for approx. 6 s and goes out.

CLOCK SPRING ADJUSTMENT

NOTE:

1. Set the front tires straight-ahead.

CAUTION:

2. Turn the clock spring clockwise until it stops.

Mazda 2. CLOCK SPRING ADJUSTMENT

3. From the stopped position, turn the clock spring counterclockwise 2 1/2 turns.

Mazda 2. CLOCK SPRING ADJUSTMENT

4. Align the marks.

Mazda 2. CLOCK SPRING ADJUSTMENT

CLOCK SPRING INSPECTION

1. Switch the ignition to off.

2. Disconnect the negative battery cable and wait for 1 min or more.

3. Remove the following parts:

  1. Driver-side air bag module (See DRIVER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION).
  2. Steering wheel (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION).
  3. Column cover (See COLUMN COVER REMOVAL/INSTALLATION).
  4. Clock spring (See CLOCK SPRING REMOVAL/INSTALLATION).

4. Verify that the continuity is as indicated in the table.

NOTE:

Mazda 2. CLOCK SPRING INSPECTION

Mazda 2. CLOCK SPRING INSPECTION

PASSENGER AIR BAG DEACTIVATION (PAD) INDICATOR LIGHT REMOVAL/INSTALLATION

NOTE:

1. Remove the PAD indicator light. (See CENTER PANEL UNIT DISASSEMBLY/ASSEMBLY).

PASSENGER AIR BAG DEACTIVATION (PAD) INDICATOR LIGHT INSPECTION

Mazda 2. PASSENGER AIR BAG DEACTIVATION (PAD) INDICATOR LIGHT INSPECTION

READ NEXT:

 Air Bag Module and Pre-tensioner Seat Belt Deployment Procedures

WARNING: A live (undeployed) air bag module or pre-tensioner seat belt may accidentally operate (deploy) when it is disposed of and cause serious injury. Do not dispose of a live (undeployed) a

 Inspection of SST (Deployment Tool)

1. Before using the SST (49 H066 002), inspect its operation. Inspection Procedure 1. Follow the steps below to inspect the SST (49 H066 002). If not as indicated in the table, replace the SST (49

 Body and Accessories

SEE MORE:

 Transaxle Fluid Temperature (TFT) Sensor

TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR INSPECTION CAUTION: Water or foreign objects entering the connector can cause a poor connection or corrosion. Be sure not to drop water or foreign objects on the connector when disconnecting it. On-Vehicle Inspection 1. Disconnect the coupler compone

 Drive Plate

DRIVE PLATE REMOVAL/INSTALLATION 1. Remove the transaxle. (See AUTOMATIC TRANSAXLE REMOVAL/INSTALLATION). 2. Remove in the order indicated in the table. 3. Install in the reverse order of removal. Drive plate installation bolts Adapter Drive plate Drive Plate Installation Bolts Removal Note

© 2016-2022 Copyright www.m2info.net