Mazda 2: Center Ventilator Grille

CENTER VENTILATOR GRILLE REMOVAL/INSTALLATION

Removal

1. Route the wiring harness as shown in the figure and pull on the center ventilator grille in the direction of the arrow to remove it.

Installation

NOTE:

1. Insert a flathead screwdriver into the position shown in the figure.

2. Move a flathead screwdriver in the direction of the arrow and detach the hook, while pull the center ventilator grille.

3. Remove the center ventilator grille in the direction of the arrow from the center ventilator grille cover.

4. Push the center ventilator grille in the direction of the arrow and install it.

VENTILATOR GRILLE REMOVAL/INSTALLATION

1. Remove the following parts:

  1. Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION).
  2. Front side trim (See FRONT SIDE TRIM REMOVAL/INSTALLATION).
  3. Rear console (See REAR CONSOLE REMOVAL/INSTALLATION).
  4. Shift lever knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION).
  5. Side wall (See SIDE WALL REMOVAL/INSTALLATION).
  6. Front console component (See FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION).
  7. Hood release lever (See HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION).
  8. Lowre panel (See LOWER PANEL REMOVAL/INSTALLATION).
  9. Side panel (See SIDE PANEL REMOVAL/INSTALLATION).

2. Rotate the ventilator grille to the notch in the direction of the arrow (1) shown in the figure and pull it in the direction of the arrow (2) to remove it.

3. Install in the reverse order of removal.

SIDE WALL REMOVAL/INSTALLATION

Right-side

1. Remove the fastener.

2. Pull the side wall in the direction of the arrow in the order of (1) and (2), then remove it while detaching clips A and tab B.

3. Install in the reverse order of removal.

Left-side

1. Remove the fastener.

2. Pull the side wall in the direction of the arrow in the order of (1) and (2), then remove it while detaching clips A and B and tab C.

3. Install in the reverse order of removal.

INNER GARNISH REMOVAL/INSTALLATION

1. Disconnect the negative battery cable (vehicles with tweeter).

2. Pull the inner garnish in the direction of the arrow shown in the figure and remove it while detaching the clips.

3. Disconnect the tweeter connector (vehicles with tweeter).

4. Install in the reverse order of removal.

SIDE PANEL REMOVAL/INSTALLATION

1. Partially peel back the seaming welt.

2. Remove the following parts:

  1. Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION).
  2. Front side trim (See FRONT SIDE TRIM REMOVAL/INSTALLATION).
  3. Rear console (See REAR CONSOLE REMOVAL/INSTALLATION).
  4. Shift lever knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION).
  5. Side wall (See SIDE WALL REMOVAL/INSTALLATION).
  6. Front console component (See FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION).
  7. Hood release lever (See HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION).
  8. Lowre panel (See LOWER PANEL REMOVAL/INSTALLATION).

3. Pull the side panel in the direction of the arrow shown in the figure and remove it while detaching clips A and B.

4. Install in the reverse order of removal.

DASHBOARD UNDER COVER REMOVAL/INSTALLATION

1. While pressing the hook inside the service hole in the direction of the arrow (1) shown in the figure, pull the dashboard under cover in the direction of the arrow (2), and then remove the hook and the guide pin.

2. Remove the dashboard under cover.

3. Install in the reverse order of removal.

READ NEXT:

 Front Console Component

FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION 1. Shift lever to neutral position. 2. Remove the following parts: Rear console (See REAR CONSOLE REMOVAL/INSTALLATION). Side wall (See SIDE WALL REMOV

 Front Door Trim

FRONT DOOR TRIM REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the inner garnish. (See INNER GARNISH REMOVAL/INSTALLATION) 3. Pull the cover of inner handle while remove the

 Rear Door Trim

REAR DOOR TRIM REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the sail inner garnish. (See SAIL INNER GARNISH REMOVAL/INSTALLATION) 3. Pull the cover of inner handle while r

SEE MORE:

 Quick Release Connector

QUICK RELEASE CONNECTOR REMOVAL/INSTALLATION WARNING: Fuel is very flammable liquid. If fuel spills or leaks from the pressurized fuel system, it will cause serious injury or death and facility breakage. Fuel can also irritate skin and eyes. To prevent this, always complete the "Fuel Line Sa

 DTC U0028:88

System Malfunction Location DSC HU/CM communication fault Detection Condition WARNING: Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection with only detection conditions may cause injury due to an operating error, or damage t

© 2016-2021 Copyright www.m2info.net