Mazda 2: Blower Motor

BLOWER MOTOR REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Remove the following parts:

  1. Rear console (See REAR CONSOLE REMOVAL/INSTALLATION).
  2. Shift lever knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION).
  3. Side wall (See SIDE WALL REMOVAL/INSTALLATION).
  4. Front console component (See FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION).
  5. Front scuff plate (LH) (See FRONT SCUFF PLATE REMOVAL/INSTALLATION).
  6. Front side trim (LH) (See FRONT SIDE TRIM REMOVAL/INSTALLATION).
  7. Hood release lever (See HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION).
  8. Lower panel (driver-side) (See LOWER PANEL REMOVAL/INSTALLATION).
  9. Knee bolster (See KNEE BOLSTER REMOVAL/INSTALLATION).

3. Remove the wiring harness clip from the brake pedal.

Mazda 2. BLOWER MOTOR REMOVAL/INSTALLATION

4. Remove the brake pedal installation nuts.

Mazda 2. BLOWER MOTOR REMOVAL/INSTALLATION

5. Remove the snap pin and clevis pin.

Mazda 2. BLOWER MOTOR REMOVAL/INSTALLATION

6. Pull the power brake unit from the engine compartment side.

Mazda 2. BLOWER MOTOR REMOVAL/INSTALLATION

7. Pull the brake pedal outward while lifting it.

Mazda 2. BLOWER MOTOR REMOVAL/INSTALLATION

CAUTION:

8. Remove in the order indicated in the table.

Mazda 2. BLOWER MOTOR REMOVAL/INSTALLATION

  1. Connector
  2. Blower motor

9. Install in the reverse order of removal.

BLOWER MOTOR INSPECTION

1. Connect battery positive voltage to terminal B and ground to terminal A of the blower motor and verify its operation.

Mazda 2. BLOWER MOTOR INSPECTION

RESISTOR REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Remove in the order indicated in the table.

Mazda 2. RESISTOR REMOVAL/INSTALLATION

  1. Connector
  2. Resistor

3. Install in the reverse order of removal.

RESISTOR INSPECTION

1. Verify that the resistance between the terminals of the resistor is as shown in the table.

Mazda 2. RESISTOR INSPECTION

Mazda 2. RESISTOR INSPECTION

READ NEXT:

 Magnetic Clutch

MAGNETIC CLUTCH DISASSEMBLY/ASSEMBLY 1. Assemble in the reverse order of disassembly. Bolt Washer Pressure plate Shim Snap ring (1) A/C compressor pulley Snap ring (2) Stator A/C compressor

 Refrigerant Pressure Switch

REFRIGERANT PRESSURE SWITCH REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Collect the refrigerant. (See REFRIGERANT CHARGING). 3. Remove the ground from the engine mount No.3. 4

 Climate Control Unit

CLIMATE CONTROL UNIT REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the following parts: Glove compartment (See GLOVE COMPARTMENT REMOVAL/INSTALLATION). Dashboard under c

SEE MORE:

 Refrigerant Charging

CAUTION: Do not exceed the specification when charging the system with refrigerant. Doing so will decrease the efficiency of the air conditioner or damage the refrigeration cycle parts. Charging Recycled R-134a Refrigerant 1. Connect an R-134a recovery/recycling/recharging device to the veh

 Automatic Transaxle Controls

Various Lockouts: Indicates that you must depress the brake pedal and hold in the lock-release button to shift (The ignition must be switched ON). Indicates the selector lever can be shifted freely into any position. Indicates that you must hold in the lock-release button to shift. NO

© 2016-2021 Copyright www.m2info.net