Mazda 2: Automatic Transaxle Shift Mechanism

Mazda 2 2007-2014 Service Manual / Transmission & Transaxle / Automatic Transaxle Shift Mechanism

AUTOMATIC TRANSAXLE SHIFT MECHANISM LOCATION INDEX

Mazda 2. AUTOMATIC TRANSAXLE SHIFT MECHANISM

  1. Key cylinder
    • (See KEY INTERLOCK SYSTEM INSPECTION.)
  2. Selector lever component
    • (See AUTOMATIC TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION.)
    • (See SELECTOR LEVER INSPECTION.)
    • (See SHIFT-LOCK SYSTEM INSPECTION.)
  3. Selector cable
    • (See AUTOMATIC TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION.)
  4. Interlock cable
    • (See AUTOMATIC TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION.)
    • (See SELECTOR LEVER INSPECTION.)

AUTOMATIC TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION

CAUTION:

Selector Lever component Removal/Installation

1. Disconnect the selector lever component connector.

  1. Disconnect the negative battery cable.
  2. Remove the side wall. (See SIDE WALL REMOVAL/INSTALLATION).
  3. Remove the front console component. (See FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION).
  4. Disconnect the selector lever component connector.

Mazda 2. AUTOMATIC TRANSAXLE SHIFT MECHANISM

2. Remove the selector lever component.

  1. Disconnect the interlock cable from the selector lever component.

Mazda 2. AUTOMATIC TRANSAXLE SHIFT MECHANISM

  1. Disconnect the selector cable from the selector lever component.

Mazda 2. AUTOMATIC TRANSAXLE SHIFT MECHANISM

  1. Remove the selector lever component.

Mazda 2. AUTOMATIC TRANSAXLE SHIFT MECHANISM

3. Install in the reverse order of removal.

Selector Cable and Interlock Cable Removal/Installation

1. Disconnect the negative battery cable.

2. Remove the clip, and then disconnect the selector cable end from the manual shaft lever.

Mazda 2. AUTOMATIC TRANSAXLE SHIFT MECHANISM

3. Disconnect the selector cable from the upper transaxle bracket.

4. Remove the insulator No.1 of the exhaust system. (See EXHAUST SYSTEM REMOVAL/INSTALLATION).

5. Remove the column cover. (See COLUMN COVER REMOVAL/INSTALLATION).

6. Remove the side wall. (See SIDE WALL REMOVAL/INSTALLATION).

7. Remove the front console component. (See FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION).

8. Remove in the order indicated in the figure.

9. Install in the reverse order of removal.

Mazda 2. AUTOMATIC TRANSAXLE SHIFT MECHANISM

  1. Interlock cable
  2. Selector cable

Selector Cable Removal Note

1. Working with two people, one person pushes the ends of the selector cable toward the inside of the vehicle, and at the same time, the other person pulls out the selector cable by pulling the ends of the selector cable.

Mazda 2. AUTOMATIC TRANSAXLE SHIFT MECHANISM

Selector Cable Installation Note

1. Working with two people, one person pushes the ends of the selector cable toward the lower side of the vehicle from the inside, and at the same time, the other person pulls the ends of the selector cable.

Mazda 2. AUTOMATIC TRANSAXLE SHIFT MECHANISM

Interlock Cable Installation Note

1. Install the interlock cable to the key cylinder.

  1. Switch the ignition to ACC.
  2. Install the interlock cable end to the key cylinder.

2. Install the lock unit to the brake pedal.

  1. Align the slide pin with the marking of the lock unit.

Mazda 2. AUTOMATIC TRANSAXLE SHIFT MECHANISM

  1. Insert a snap pin (or a round bar of 1.5 mm {0.059 in} diameter) into hole A with the slide pin inserted completely.

Mazda 2. AUTOMATIC TRANSAXLE SHIFT MECHANISM

  1. Insert the other snap pins through hole B and hole C.
  2. Replace the brake switch with a new one. (See BRAKE PEDAL REMOVAL/INSTALLATION).
  3. Install the lock unit to the brake pedal bracket.
  4. Rotate the slide pin 90

      READ NEXT:

       Steering

       Electric Power Steering (EPS)

      ELECTRIC POWER STEERING (EPS) SYSTEM WIRING DIAGRAM ELECTRIC POWER STEERING (EPS) ON-BOARD DIAGNOSIS On-Board Diagnostic (OBD) Test Description The OBD test inspects the integrity and function of t

       General Procedures

      WARNING: Always inspect the steering component carefully for any shock or impact which may have occurred during a collision or servicing operation. If a damaged part or a part suspected of bei

      SEE MORE:

       Front Outer Handle

      FRONT OUTER HANDLE REMOVAL/INSTALLATION 1. To access the glass installation bolt, position the front door glass so that the distance from the top of the front door glass to the upper part of the front beltline molding is approx. 110 mm {4.33 in}. 2. Disconnect the negative battery cable. 3. Rem

       Running Out of Fuel (SKYACTIV-D 1.5)

      CAUTION Do not try starting the engine for more than 30 seconds at a time. Doing so, could damage the starter. If the engine does not start on the fi rst try wait about 10 seconds before trying again. If your vehicle runs out of fuel, add at least 10 L (2.6 US gal, 2.2 Imp gal) of fuel, and

    © 2016-2021 Copyright www.m2info.net