Mazda 2: Automatic Transaxle
Mazda 2 2007-2014 Service Manual / Transmission & Transaxle / Automatic Transaxle
AUTOMATIC TRANSAXLE LOCATION INDEX
- Drive plate
- (See DRIVE PLATE REMOVAL/INSTALLATION)
- Input/turbine speed sensor
- (See INPUT/TURBINE SPEED SENSOR INSPECTION)
- (See INPUT/TURBINE SPEED SENSOR REMOVAL/INSTALLATION)
- VSS
- (See VEHICLE SPEED SENSOR (VSS) INSPECTION)
- (See VEHICLE SPEED SENSOR (VSS) REMOVAL/INSTALLATION)
- Pressure control solenoid
- Shift solenoid A
- Shift solenoid B
- Shift solenoid C
- Shift solenoid D
- Shift solenoid E
- (See SOLENOID VALVE INSPECTION)
- (See SOLENOID VALVE REMOVAL/INSTALLATION)
- TFT sensor
- (See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR INSPECTION)
- (See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR REMOVAL/INSTALLATION)
- Oil seal
- (See OIL SEAL REPLACEMENT)
- Control valve body
- (See CONTROL VALVE BODY REMOVAL/INSTALLATION)
- TR switch
- (See TRANSAXLE RANGE (TR) SWITCH INSPECTION)
- (See TRANSAXLE RANGE (TR) SWITCH ADJUSTMENT)
- (See TRANSAXLE RANGE (TR) SWITCH REMOVAL/INSTALLATION)
- Automatic transaxle
- (See MECHANICAL SYSTEM TEST)
- (See ROAD TEST)
- (See AUTOMATIC TRANSAXLE FLUID (ATF) INSPECTION)
- (See AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT)
- (See AUTOMATIC TRANSAXLE REMOVAL/INSTALLATION)
- Oil cooler
- (See OIL COOLER REMOVAL/INSTALLATION)
- (See OIL COOLER FLUSHING)
- O/D OFF switch
- (See O/D OFF SWITCH INSPECTION)
- (See O/D OFF SWITCH REMOVAL/INSTALLATION)
- PCM
- (See PCM INSPECTION)
- (See PCM REMOVAL/INSTALLATION)
- Mechanical System Test
- Road Test
- Automatic Transaxle Fluid (ATF)
- Transaxle Range (TR) Switch
- Transaxle Fluid Temperature (TFT) Sensor
- Input/Turbine Speed Sensor
- Vehicle Speed Sensor (VSS)
- Solenoid Valve
- PCM
- Drive Plate
- Oil Seal
- Control Valve Body
READ NEXT:
Mechanical System Test
Mechanical System Test Preparation
1. Engage the parking brake and use wheel chocks at the front and rear of the
wheels.
2. Inspect the engine coolant. (See ENGINE COOLANT LEVEL INSPECTION).
3. Ins
Road Test
WARNING:
When performing a road test, be aware of other vehicles, people,
impediments, etc. to avoid an accident.
NOTE:
When the legal speed limit must be exceeded, use a chassis dynamometer.
Automatic Transaxle Fluid (ATF)
AUTOMATIC TRANSAXLE FLUID (ATF) INSPECTION
Automatic transaxle Fluid (ATF) Condition Inspection
1. Remove the dipstick.
2. One way of determining whether the transaxle should be disassembled is by
n
SEE MORE:
Wheel and Tire Specification
Standard tire
*3 Verify the tire label attached to the actual vehicle on vehicles without
TPMS.
Spare tire
WHEEL BALANCE ADJUSTMENT (ALUMINUM ALLOY WHEEL)
CAUTION:
Adjust the outer wheel balance first, then the inner wheel balance.
Be careful not to scratch the wheels.
Adhesive-type Balance
Input/Turbine Speed Sensor
INPUT/TURBINE SPEED SENSOR INSPECTION
CAUTION:
Water or foreign objects entering the connector can cause a poor
connection or
corrosion. Be sure not to drop water or foreign objects on the connector
when
disconnecting it.
On-Vehicle Inspection
1. Disconnect the input/turbine speed sensor co
© 2016-2021 Copyright www.m2info.net