Mazda 2: Airflow Mode Link Set

AIRFLOW MODE LINK SET REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Remove the following parts:

  1. Rear console (See REAR CONSOLE REMOVAL/INSTALLATION).
  2. Shift lever knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION).
  3. Side wall (See SIDE WALL REMOVAL/INSTALLATION).
  4. Front console component (See FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION).
  5. Front scuff plate (LH) (See FRONT SCUFF PLATE REMOVAL/INSTALLATION).
  6. Front side trim (LH) (See FRONT SIDE TRIM REMOVAL/INSTALLATION).
  7. Hood release lever (See HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION).
  8. Lower panel (driver-side) (See LOWER PANEL REMOVAL/INSTALLATION).
  9. Knee bolster (See KNEE BOLSTER REMOVAL/INSTALLATION).
  10. Heat duct (LH) (See HEAT DUCT COMPONENT REMOVAL/INSTALLATION).

3. Remove the wiring harness clip from the brake pedal.

Mazda 2. AIRFLOW MODE LINK SET REMOVAL/INSTALLATION

4. Remove the brake pedal installation nuts.

Mazda 2. AIRFLOW MODE LINK SET REMOVAL/INSTALLATION

5. Remove the snap pin and clevis pin.

Mazda 2. AIRFLOW MODE LINK SET REMOVAL/INSTALLATION

6. Pull the power brake unit from the engine compartment side.

Mazda 2. AIRFLOW MODE LINK SET REMOVAL/INSTALLATION

7. Pull the brake pedal outward while lifting it.

Mazda 2. AIRFLOW MODE LINK SET REMOVAL/INSTALLATION

CAUTION:

8. Remove in the order indicated in the table.

Mazda 2. AIRFLOW MODE LINK SET REMOVAL/INSTALLATION

  1. Airflow mode rod
  2. Link collar (1)
  3. Airflow mode main link
  4. Link collar (2)
  5. Airflow mode sub link (1)
  6. Link collar (3)
  7. Airflow mode sub link (2)
  8. Airflow mode crank (1)
  9. Airflow mode crank (2)
  10. Link collar (4) (manual air conditioner)
  11. Airflow mode sub link (3) (manual air conditioner)

9. Install in the reverse order of removal.

AIR MIX LINK SET REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Remove the following parts:

  1. Glove compartment (See GLOVE COMPARTMENT REMOVAL/INSTALLATION).
  2. Dashboard under cover (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION).
  3. Heat duct (RH) (See HEAT DUCT COMPONENT REMOVAL/INSTALLATION).
  4. Rear console (See REAR CONSOLE REMOVAL/INSTALLATION).
  5. Shift lever knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION).
  6. Side wall (See SIDE WALL REMOVAL/INSTALLATION).
  7. Front console component (See FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION).

3. Disconnect the air mix wire.

CAUTION:

4. Remove in the order indicated in the table.

Mazda 2. AIR MIX LINK SET REMOVAL/INSTALLATION

  1. Air mix crank
  2. Link collar (5)
  3. Air mix link

5. Install in the reverse order of removal.

AIR INTAKE LINK SET REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

2. Remove the following parts:

  1. Glove compartment (See GLOVE COMPARTMENT REMOVAL/INSTALLATION).
  2. Dashboard under cover (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION).
  3. Heat duct (RH) (See HEAT DUCT COMPONENT REMOVAL/INSTALLATION).
  4. Rear console (See REAR CONSOLE REMOVAL/INSTALLATION).
  5. Shift lever knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION).
  6. Boot panel (See FRONT CONSOLE COMPONENT DISASSEMBLY/ASSEMBLY).
  7. Side wall (See SIDE WALL REMOVAL/INSTALLATION).
  8. Front console component (See FRONT CONSOLE COMPONENT REMOVAL/INSTALLATION).
  9. Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION).
  10. Front side trim (See FRONT SIDE TRIM REMOVAL/INSTALLATION).
  11. Hood release lever (See HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION).
  12. Lower panel (driver-side) (See LOWER PANEL REMOVAL/INSTALLATION).
  13. Driver-side air bag module (See DRIVER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION).
  14. Knee bolster (See KNEE BOLSTER REMOVAL/INSTALLATION).
  15. Steering wheel (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION).
  16. Column cover (See COLUMN COVER REMOVAL/INSTALLATION).
  17. Meter hood (See METER HOOD REMOVAL/INSTALLATION).
  18. Instrument cluster (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION).
  19. Combination switch (See COMBINATION SWITCH REMOVAL/INSTALLATION).
  20. Center panel unit (See CENTER PANEL UNIT REMOVAL/INSTALLATION).
  21. Climate control unit (See CLIMATE CONTROL UNIT REMOVAL/INSTALLATION [MANUAL AIR CONDITIONER] ).
  22. Shift lever component (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION).
  23. Selector lever component (ATX) (See AUTOMATIC TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION
  24. Interlock unit (ATX) (See AUTOMATIC TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION).
  25. Lower panel (passenger-side) (See LOWER PANEL REMOVAL/INSTALLATION).
  26. Side panel (See SIDE PANEL REMOVAL/INSTALLATION).
  27. A-pillar trim (See A-PILLAR TRIM REMOVAL/INSTALLATION).
  28. Windshield wiper arm and blade (See WINDSHIELD WIPER ARM AND BLADE REMOVAL/INSTALLATION).
  29. Cowl grille (See COWL GRILLE REMOVAL/INSTALLATION).
  30. Windshield wiper motor (See WINDSHIELD WIPER MOTOR REMOVAL/INSTALLATION).
  31. Sail garnish (See SAIL GARNISH REMOVAL/INSTALLATION).
  32. Steering shaft cover (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION).
  33. Steering shaft (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION).

3. Disconnect the dashboard wiring harness connector.

4. Disconnect the antenna feeder No.1 jack.

5. Remove the dashboard. (See DASHBOARD REMOVAL/INSTALLATION).

6. Disconnect the air intake wire. (See CLIMATE CONTROL UNIT REMOVAL/INSTALLATION [MANUAL AIR CONDITIONER] ).

CAUTION:

7. Remove in the order indicated in the table.

Mazda 2. AIR INTAKE LINK SET REMOVAL/INSTALLATION

  1. Bushing nut
  2. Spring
  3. Link collar
  4. Air intake link
  5. Air intake crank

8. Install in the reverse order of removal.

READ NEXT:

 Heat Duct Component

HEAT DUCT COMPONENT REMOVAL/INSTALLATION Heat Duct (LH) 1. Disconnect the negative battery cable. 2. Remove the following parts: Rear console (See REAR CONSOLE REMOVAL/INSTALLATION). Shift lever k

 A/C Compressor

A/C COMPRESSOR REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the splash shield (RH). 3. Collect the refrigerant. (See REFRIGERANT CHARGING). 4. Remove the drive belt. (Se

 Condenser

CONDENSER REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Collect the refrigerant. (See REFRIGERANT CHARGING). 3. Drain the engine coolant. (See ENGINE COOLANT REPLACEMENT] ). 4.

SEE MORE:

 On-Board Diagnostic System

ON-BOARD DIAGNOSTIC SYSTEM WIRING DIAGRAM NOTE: Only the transaxle-related information is described. ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION DTC Inspection Procedure (See ON-BOARD DIAGNOSTIC TEST). DTC Clearing Procedure (See AFTER REPAIR PROCEDURE). ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE DTC

 Aerial

Embedded Type * The aerial is embedded into the window glass. CAUTION When washing the inside of the window which has an aerial, use a soft cloth dampened in lukewarm water, gently wiping the aerial lines. Use of glass cleaning products could damage the aerial. Detachable Type To remove

© 2016-2021 Copyright www.m2info.net